Utility Mode - Fender B-DEC 30 Mode D'emploi

1

Utility Mode

Use Utility Mode to rename presets, lock memory, transfer presets (MIDI) and manage the system.
 M enu UtilityMenuItems
 1 MIDI LEVEL
2 EDIT PRESET NAME
3 LINE OUT
4 SPEAKER
5 MEMORY LOCK
6 DUMP PRESET
7 DUMP ALL
8 MIDI CONTROL
9 DEFAULT QA1
10 DEFAULT QA2
11 DEFAULT QA3
12 FACTORY RESTORE
13 AMP UPDATE
Phrase Sampler
GENERAL NOTES:
(Phrase Sampler behavior that you should know about)
DUB: This button is ignored if the amp is set to half speed playback.
OVRDUBFBCK: The Overdub Feedback setting (found in the Aux menu) controls the level of decay (fade out) of the
previously recorded signal when overdubbing (10.0 = no decay). Overdubbing only records the bass
signals. MIDI patterns are stopped before overdubbing and cannot be restarted until overdubbing is
complete.
PhraseSamplerStatesandControls
oFF
(If you start with the Phrase Sampler "OFF," pressing "PLAY", "REC" or "DUB" will cause this to happen)...
PLAY: Start playback if a loop has been previously recorded, ignore otherwise.
RECORD:
Enter record mode and start recording.
OVERDUB: Start overdubbing if a loop has been previously recorded, otherwise start recording.
PLAYIng
(If you start with the Phrase Sampler "PLAYING," pressing "PLAY", "REC" or "DUB" will cause this to happen)...
PLAY:
Stop playback.
RECORD: Enter record mode and start recording.
OVERDUB:
Start overdubbing on next pass through (tapping again, prior to the overdubbing starting, cancels
overdubbing before it starts and continues playback).
reCordIng
(If you start with the Phrase Sampler "RECORDING," pressing "PLAY", "REC" or "DUB" will cause this to happen)...
PLAY: Exit record mode and begin playback (truncates loop to nearest measure if the amp is set to 4 beat lead
in mode).
RECORD: Stop the recording process.
OVERDUB: Exit record mode and begin playback and begin overdubbing (truncates loop to nearest measure if the
amp is set to 4 beat lead in mode).
oVerdUBIng
(If you start with the Phrase Sampler "DUBBING," pressing "PLAY", "REC" or "DUB" will cause this to happen)...
PLAY: Stop overdubbing and continue playback on next pass through.
RECORD: Enter record mode and start recording.
OVERDUB: Stop overdubbing and playback on next pass through.
All manuals and user guides at all-guides.com
B-DEC 3O
Procedure—(Function)
Rotate Data Wheel — (MIDI level)
Rotate Data Wheel, then follow the instructions displayed on screen.
Rotate Data Wheel — (Select All or MIDI to be supplied to the LINE OUT jack.)
Rotate Data Wheel — (Select All or Bass + AUX IN (and Phrase) to output to the speaker.)
Rotate Data Wheel — (Prevents accidental preset saves and MIDI dumps, but NOT a Factory Reset, see below.)
Press "SAVE" — (Transfers the current preset to another B–DEC™ 30 or computer connected to the MIDI OUT port.)
Press "SAVE" — (Transfers ALL presets to another B–DEC 30 or computer connected to the MIDI OUT port.)
Rotate Data Wheel — (Select AMP or MIDI see page 20)
Rotate Data Wheel — (Select the default Bass Preset to be assigned when creating a new S bank preset)
Rotate Data Wheel — (Select the default Bass Preset to be assigned when creating a new S bank preset)
Rotate Data Wheel — (Select the default Bass Preset to be assigned when creating a new S bank preset)
Press "SAVE" twice — (Restores every B–DEC 30 setting to the original settings. OVERRIDES MEMORY LOCK.)
(Reserved for future B–DEC 30 software updates.)
(how the current state affects what each of the buttons do)
f e n d e r . c o m