Installation; General; Preparing The Unit For Installation - Hatco FTB Série Manuel D'installation Et D'utilisation

English

General

Frost Top Drop-In Shelves are shipped from the factory
completely assembled and ready for use. Use the following
information and procedures to prepare the unit and installation
site as well as to install the unit.
WARNING
ELECTRIC SHOCK HAzARD:
• Plug unit into a properly grounded electrical receptacle
of the correct voltage, size, and plug configuration. If
plug and receptacle do not match, contact a qualified
electrician to determine and install proper voltage and
size electrical receptacle.
• Unit is not weatherproof. Locate unit indoors.
FIRE HAzARD: Install unit with a minimum of 2" (51 mm) of
space between all sides of the condensing unit and any
combustible surfaces.
This unit must be installed by qualified, trained installers.
Installation must conform to all local electrical and
plumbing codes. Check with local plumbing and electrical
inspectors for proper procedures and codes.
CAUTION
Locate unit at the proper counter height in an area that is
convenient for use. Location should be level and strong
enough to support weight of unit and contents.
NOTICE
Transport and install unit in upright position only. Failure
to do so may result in damage to the refrigeration system.
When shipped during cold weather months, store unit in
proper ambient temperature environment for 10 hours to
prevent compressor and/or refrigerant line damage. If unit is
turned on and there is excessive noise and vibration, turn
off immediately and allow additional warm up time.
This unit is designed for use in environments where the
ambient temperature is between 65°F (18°C) and 86°F (30°C).
Provide louvered or grill-style openings with a minimum
size of 12" x 12"/144 square inches (31 x 31 cm/
961 square cm) in the cabinetry in front of and behind the
condensing unit for proper ventilation. Failure to provide
adequate air flow through the condensing unit may cause
unit failure and will void the unit warranty.
Do not locate unit in an area subject to excessive
temperatures or grease from grills, fryers, etc. Excessive
temperatures could cause damage to the unit.
All Frost Top Drop-In Shelves are shipped in a wooden frame
for protection and stability. Keep the unit in the wooden frame
until the unit and the installation site are completely prepared for
the unit to be installed.
1. Remove all external packaging from the unit.
2. Remove tape, protective packaging, and literature from all
surfaces of unit.
NOTE: To prevent delay in obtaining warranty coverage,
complete online warranty registration. See the
ImPORTANT OWNER INFORmATION section for
details.
Form No. FTBm-1015

Preparing the Unit for Installation

The orientation of the condensing unit on all FTB models can be
adjusted to match the layout of the installation site. It can be
rotated 90° or 180° from its factory-installed position. On
FTB-3, FTB-S2, and FTB-S3 models, the condensing unit can
be installed in several positions along the bottom of the frost
top enclosure using pre-drilled holes at 6-1/2" (165 mm)
increments. The condensing unit on FTB-2 models can be
installed in pre-drilled holes at 3" (76 mm) increments.
Survey the installation site and determine if adjustment to the
orientation and/or position of the condensing unit is necessary.
Take into account the need for louvered or grill-style openings
in the cabinetry to provide proper ventilation for the condensing
unit as well as access to the control panel. One of these
ventilation openings must be in front of the condensing coils
with the other on the opposite side. If adjustment to the
orientation and/or position of the condensing unit is necessary,
use the following procedure(s).
Rotating the Condensing Unit
This procedure can be performed on all FTB models.
1. Place blocks underneath the condensing unit for support
during rotation.
2. Remove the 4 mounting screws that secure the condensing
unit support frame to the underside of the frost top enclosure.
3. Rotate the condensing unit 90° or 180°, depending on the
installation site.
NOTE: Do not rotate the condensing unit in a direction that will
put the evaporator lines or any other obstruction in front
of the condenser coil.
4. Reattach the condensing unit support frame to the underside
of the frost top enclosure using the 4 mounting screws.
Condensing Unit
Support Frame
Mounting
Screw
Rotating the Condensing Unit
7

INSTALLATION

Hoses removed
for clarity.
Condensing Unit
rotated 90°.