Other Precautions - Canon WG7000 Serie Démarrage

cleaning automatically. To do this, the machine
occasionally draws ink from the nozzles, and
thus may use a minute amount of ink.
• Even with black and white printing, ink colors
other than black may be used depending on
the type of paper being printed on or on
settings in the printer driver.

Other Precautions

• Do not remove the print head unnecessarily.
• Not printing for a long period of time may
cause the print head to dry out and clog. It is
recommended that the machine be used for
printing at least once a month.
Notice
Caution for each safety standard
mark and declaration
Each safety standard mark and declaration is
valid only for the voltage and frequency of the
respective country or region where it applies.
Safety-Related Symbols
Protective earthing terminal
CAUTION: Hot surface. Do not touch.
Moving parts: Keep body parts away from
moving parts. Keep body parts out of the
motion path.
* This mark may not appear on your model.
Product Name
Safety regulations require the product's name to
be registered.
In some regions where this product is sold, the
following name(s) in parentheses ( ) may be
registered instead.
RMC(Regulatory Model Code)
WG7250Z (K10479)
WG7250F (K10478)
WG7250 (K10477)
WG7240 (K10476)
Precaution for Using This Product in
Countries or Regions other than where It was
Purchased
This product, which is made for countries or
regions where it was purchased, may not be
used in other countries or regions due to their
local laws and regulations. Please note that
Canon should not be liable for penalties which
will be caused by using this product in such
countries or regions.
About Radio Waves
Do not use this product near medical equipment
or electronic equipment. Radio wave
interference can affect the operation or
performance of the equipment.
For models containing lithium battery
• Dispose of used batteries according to the
local regulations.
• Risk of explosion if battery is replaced by an
incorrect type.
Users in the U.S.A.
FCC Notice (U.S.A. Only)
For 120V, 60Hz model
Model Number: K10476
Optional parts: Cassette Feeding Unit CF10
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation.
Note: This equipment has been tested and
found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used
in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to
radio or television reception, which can be
determined by turning the equipment off and
on, the user is encouraged to try to correct the
interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/
TV technician for help.
Use of a shielded cable is required to comply
with Class B limits in Subpart B of Part 15 of the
FCC Rules.
Do not make any changes or modifications to
the equipment unless otherwise specified in the
manual. If such changes or modifications should
be made, you could be required to stop
operation of the equipment.
Canon U.S.A., Inc.
One Canon Park
Melville, New York 11747
1-800-652-2666
Users in the U.S.A.
FCC Notice (U.S.A. Only)
For 120V, 60Hz model
Model Number: K10477/K10478/K10479
(Contains FCC Approved WLAN Module
AW-NM383)
Optional parts: Cassette Feeding Unit CF10
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation.
Note: This equipment has been tested and
found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used
in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to
radio or television reception, which can be
determined by turning the equipment off and
on, the user is encouraged to try to correct the
interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/
TV technician for help.
Use of a shielded cable is required to comply
with Class B limits in Subpart B of Part 15 of the
FCC Rules.
Do not make any changes or modifications to
the equipment unless otherwise specified in the
manual. If such changes or modifications should
be made, you could be required to stop
operation of the equipment.
FCC ID:TLZ-NM383
Changes or modifications not expressly
approved by the party responsible for
compliance could void the user's authority to
operate equipment.
This transmitter must not be co-located or
operating in conjunction with any other antenna
or transmitter.
The equipment complies with FCC radiation
exposure limits for at uncontrolled equipment.
This equipment should be installed and
operated with minimum distance at least 20cm
between the radiator and persons body
(excluding extremities: hands, wrists, feet and
ankles) and must not be colocated or operated
with any other antenna or transmitter.
Canon U.S.A., Inc.
One Canon Park
Melville, New York 11747
1-800-652-2666
Disclaimers
• The information in this document is subject
to change without notice.
• CANON INC. MAKES NO WARRANTY OF ANY
KIND WITH REGARD TO THIS MATERIAL,
EITHER EXPRESS OR IMPLIED, EXCEPT AS
PROVIDED HEREIN, INCLUDING WITHOUT
LIMITATION, THEREOF, WARRANTIES AS TO
MARKETABILITY, MERCHANTABILITY, FITNESS
FOR A PARTICULAR PURPOSE OF USE, OR
NON-INFRINGEMENT. CANON INC. SHALL
NOT BE LIABLE FOR ANY DIRECT, INCIDENTAL,
OR CONSEQUENTIAL DAMAGES OF ANY
NATURE, OR LOSSES OR EXPENSES RESULTING
FROM THE USE OF THIS MATERIAL.
Users in the U.S.A.
Pre-Installation Requirements for Canon
Facsimile Equipment
Pre-Installation Requirements
Order Information
When ordering service from the telephone
company for this equipment, the following may
be required.
Universal Service Order Code (USOC): RJ11C
The Facility Interface Code (FIC): 02LS2
Service Order Code (SOC): 9.0F
Connection of the Equipment
This equipment complies with Part 68 of the FCC
rules and the requirements adopted by the
ACTA.
A label on this equipment contains, among
other information, a product identifier in the
format US:AAAEQ##TXXXX. If requested, this
number must be provided to the telephone
company.
The REN is used to determine the number of
devices that may be connected to a telephone
line.
Excessive RENs on a telephone line may result in
the devices not ringing in response to an
incoming call. In most but not all areas, the sum
of RENs should not exceed five (5.0). To be
certain of the number of devices that may be
connected to a line, as determined by the total
RENs, contact the local telephone company. The
REN for this product is part of the product
identifier that has the format
US:AAAEQ##TXXXX. The digits represented by
EN
41