Table des Matières
Publicité
Chapitre 13.0 Déclarations des organismes de réglementation
13.0 Déclarations des organismes de réglementation
FCC MODIFICATION STATEMENT
Digital Security Controls has not approved any changes or modifications to this device by the user. Any changes or modifications could void the user's authority to ope-
rate the equipment
.Digital Security Controls n'approuve aucune modification apportée à l'appareil par l'utilisateur, quelle qu'en soit la nature. Tout changement ou modification peuvent
annuler le droit d'utilisation de l'appareil par l'utilisateur.
FCC AND ISED CANADA INTERFERENCE STATEMENT
This device complies with Part 15 of the FCC Rules and ISED Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'ISED Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions sui-
vantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, ême si le brouillage est sus-
ceptible d'en compromettre le fonctionnement.
FCC CLASS B DIGITAL DEVICE NOTICE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to pro-
vide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equip-
ment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or experienced radio/television technician for help.
CAN ICES-3 (B) / NMB-3 (B)
The reference to the WS900-xx throughout this manual is applicable to the following model numbers: WS900-19 and WS900-29.
FCC ID:F5316WS90019
FCC ID:F5316WS900-29
IC: 160A-WS90019
IC: 160A-WS90029
The reference to the Cellular Communicator xx7090 throughout this manual is applicable to the following model numbers: 3G7090 and LT7090.
FCC ID:F53163G7090
FCC ID:F5316LT7090
IC: 160A-3G7090
IC: 160A-LT7090
FCC/ISED CANADA WIRELESS NOTICE
WARNING: To satisfy FCC RF exposure requirements for mobile transmitting devices, a separation dis-
tance of 20cm or more must be maintained between the antenna of this device and persons during d evice
operation.
Antenna gain must be below:
Frequency band
GSM 850 / FDD V
PCS 1900 / FDD II
LTE B4 (1700 MHz)
LTE B13 (700 MHz)
The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter, except as described in this user
manual.
AVERTISSEMENT: Pour satisfaire aux recommandations d'exposition RF FCC des dispositifs de trans-
mission mobile, un espace de séparation de 20 cm ou plus doit être maintenu entre l'antenne de l'ap-
pareil et les personnes pendant son fonctionnement.
Gain de l'antenne doit être ci-dessous:
Frequency band
GSM 850 / FDD V
PCS 1900 / FDD II
LTE B4 (1700 MHz)
LTE B13 (700 MHz)
Les antennes utilisées avec ce produit ne doivent pas être placées ni utilisées en association avec une autre antenne ou un autre émetteur, comme indiqué dans ce
manuel
FCC/IC LABEL
A label is shipped together with the module and it is the responsibility of the integrator to apply it to the exterior of the enclosure, as displayed in the following figure.
Une étiquette est livré avec le module et il est de la responsabilité de l'intégrateur de l'appliquer à l'extérieur de l'enceinte, comme indiqué dans la figure suivante.
3G4000
2.1 dBi
3.7 dBi
1.5 dBi
2.2 dBi
3G4000
2.1 dBi
3.7 dBi
1.5 dBi
2.2 dBi
- 35 -
Publicité
Table des Matières
