Makita GD0800C Manuel D'instructions page 3

ENGLISH
(Original instructions)
1 Slide switch
2 Speed adjusting dial
SPECIFICATIONS
Model
Collet size ....................................................................................8 mm max.
Max. wheel point size
Max. wheel diameter ................................................................25 mm
Max. mandrel (shank) length ....................................................46 mm
Rated speed (n) / No load speed (n
Overall length ..............................................................................371 mm
Net weight ....................................................................................1.7 kg
Safety class .................................................................................. /II
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for grinding ferrous materials or
deburring castings.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.
DIE GRINDER SAFETY WARNINGS
Safety Warnings Common for Grinding Operation:
1. This power tool is intended to function as a
grinder. Read all safety warnings, instructions,
illustrations and specifications provided with
this power tool. Failure to follow all instructions
listed below may result in electric shock, fire and/or
serious injury.
2. Operations such as sanding, wire brushing, pol-
ishing or cutting-off are not recommended to be
performed with this power tool. Operations for
which the power tool was not designed may create a
hazard and cause personal injury.
3. Do not use accessories which are not specifi-
cally designed and recommended by the tool
manufacturer. Just because the accessory can be
attached to your power tool, it does not assure safe
operation.
Explanation of general view
3 Side handle
4 Wrench 19
)...........................................28,000 (min
0
ENE050-1
ENF002-2
GEA010-1
GEB034-9
5
6
GD0800C
–1
)
4. The rated speed of the accessory must be at
least equal to the maximum speed marked on
the power tool. Accessories running faster than
their rated speed can break and fly apart.
5. The outside diameter and the thickness of your
accessory must be within the capacity rating of
your power tool. Incorrectly sized accessories can-
not be adequately controlled.
6. The arbour size of accessories must properly fit
the collet of the power tool. Accessories that do
not match the mounting hardware of the power tool
will run out of balance, vibrate excessively and may
cause loss of control.
7. Mandrel mounted accessories must be fully
inserted into the collet or chuck. If the mandrel is
insufficiently held and/or the overhang of the wheel
is too long, the mounted accessory may become
loose and be ejected at high velocity.
8. Do not use a damaged accessory. Before each
use inspect the accessory such as abrasive
wheels for chips and cracks. If power tool or
accessory is dropped, inspect for damage or
install an undamaged accessory. After inspect-
ing and installing an accessory, position your-
self and bystanders away from the plane of the
rotating accessory and run the power tool at
maximum no-load speed for one minute. Dam-
aged accessories will normally break apart during
this test time.
9. Wear personal protective equipment. Depending
on application, use face shield, safety goggles
or safety glasses. As appropriate, wear dust
mask, hearing protectors, gloves and workshop
apron capable of stopping small abrasive or
workpiece fragments. The eye protection must be
capable of stopping flying debris generated by vari-
ous operations. The dust mask or respirator must be
capable of filtrating particles generated by your oper-
ation. Prolonged exposure to high intensity noise
may cause hearing loss.
10. Keep bystanders a safe distance away from work
area. Anyone entering the work area must wear
personal protective equipment. Fragments of
workpiece or of a broken accessory may fly away
and cause injury beyond immediate area of opera-
tion.
Wrench 13
Collet nut
GD0810C
8 mm max.
50 mm
46 mm
–1
7,000 (min )
371 mm
1.7 kg
/II
3