Festool CLEANTEX CTM 26 E Notice D'utilisation D'origine/Liste De Pièces De Rechange page 18

GB
CLEANTEX CTM/ CTM AC
SysDoc Systainer attachment system: a
Systainer can be attached to the storage area
via the two slides [8-1].
8.2 AUTOClean - Cleaning the main fil-
ter (only versions with AutoClean)
To maintain a constant suction power when ex-
tracting fine dust, you can adjust the frequency
of the automatic [1-8]
nite variables using the rotary knob. Always use
the automatic cleaning system in combination
with a disposal bag (in line with dust class 'M'
requirements).
Before performing wet extraction tasks or
working with a filter bag, set the
tary knob to position 0.
Set the automatic cleaning function to the
highest setting when
quantities of dust.
Manual cleaning
If the suction power decreases, cleaning
can be started manually by turning the
switch [1-11]
tioned on either side of the switch.
We recommend cleaning the main filter
completely if severely clogged:
Set the suction power adjuster
maximum setting.
Cover the end of the nozzle or suction hose
with your hand for 10 seconds.
Turn the switch to the
When the CT-VS closing slide is used (order
no.: 497926), the filter can be cleaned fully
without removing the connected electric
power tools.
In intensive applications that generate adher-
ent dust, it may be necessary to clean the filter
element mechanically under certain circum-
stances (extract). Wear a dust mask!
8.3 Special features of the CTM 36 E
AC- LHS
To use the mobile dust extractor in combina-
tion with the PLANEX:
Use the accompanying kink-resistant suc-
tion hose D 36 mm x 3.5 m-AS.
Use the accompanying special suction
sleeve to connect the PLANEX.
Insert the accompanying CT-VS closing
slide between the intake opening
and the suction hose.
Fit the tool holder as described in the ac-
companying installation instructions.
18
All manuals and user guides at all-guides.com
cleaning system in infi-
[1-8]
[1-8] extracting large
to the AC symbol posi-
[1-10] to the
[1-11] AC symbol.
[1-2]
When performing extraction work with the
PLANEX, always use disposal bags to pre-
vent dust from escaping into the sur-
rounding area.
8.4 Extracting dry materials
Hazardous dust
Damage to the respiratory passage
Use a filter or disposal bag when extract-
ing hazardous materials!
Do not use the machine if the volumetric
ro-
flow monitoring function is inactive.
Observe the following when extracting dust
generated by operating electric power tools:
If the exhaust air is discharged back into the
room, the air renewal rate L within the room
must be sufficient. The volume of air dis-
charged back into the room must not exceed
50% of the fresh air volume flow (room volume
V x air renewal rate L
R
vant regional regulations.
Remember: A moist main filter clogs more
quickly when extracting dry materials. There-
fore, dry the main filter before extracting dust
or replace the damp filter with a dry one.
8.5 Extracting fluids
Before extracting fluids, remove the filter or
disposal bag (see chapter 7.7). We recommend
using a special wet filter.
The dust extractor stops automatically when
the maximum level is reached.
Escaping foam and fluids
Switch off the machine immediately and
empty the dirt trap.
8.6 The antistatic system
Friction inside the extraction hose causes static
electricity to develop during extraction. Operat-
ing personnel may receive unpleasant electric
shocks while working. The mobile dust extrac-
tor is fitted with an antistatic system as stan-
dard to discharge any static electricity that may
develop. However, always use the enclosed an-
tistatic extraction hose.
CAUTION
). Observe all the rele-
W
CAUTION