Additional Safety Rules For Tool - Makita LS1016 Manuel D'instructions

Special Max. cutting capacities
Crown molding 45° type
(with Crown molding stopper used)
Base board (H)
(with Horizontal vise used)
–1
No load speed (min ) ............................................................................................................................................ 3,200
Laser Type (LS1016L, LS1016FL)..........................................................Red Laser 650 nm, <1.6 mW (Laser Class 2M)
Dimensions (L x W x H) .....................................................................................................718 mm x 640 mm x 671 mm
Net weight
For all countries other than European countries
LS1016 .............................................................................................................................................................. 23.6 kg
LS1016L/LS1016F............................................................................................................................................. 23.7 kg
LS1016FL .......................................................................................................................................................... 23.8 kg
For European countries
LS1016 .............................................................................................................................................................. 24.1 kg
LS1016L/LS1016F............................................................................................................................................. 24.2 kg
LS1016FL .......................................................................................................................................................... 24.3 kg
Safety class .............................................................................................................................................................
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for accurate straight and miter cut-
ting in wood. With appropriate saw blades, aluminum can
also be sawed.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.

ADDITIONAL SAFETY RULES FOR TOOL

1. Wear eye protection.
2. Keep hands out of path of saw blade. Avoid con-
tact with any coasting blade. It can still cause
severe injury.
3. Do not operate saw without guards in place.
Check blade guard for proper closing before
each use. Do not operate saw if blade guard
does not move freely and close instantly. Never
clamp or tie the blade guard into the open posi-
tion.
4. Do not perform any operation freehand. The
workpiece must be secured firmly against the turn
base and guide fence with the vise during all opera-
tions. Never use your hand to secure the workpiece.
5. Never reach around saw blade.
6. Turn off tool and wait for saw blade to stop
before moving workpiece or changing settings.
7. Unplug tool before changing blade or servicing.
8. Always secure all moving portions before carry-
ing the tool.
9. Stopper pin which locks the cutter head down is
for carrying and storage purposes only and not
for any cutting operations.
ENE006-1 10. Do not use the tool in the presence of flammable
liquids or gases. The electrical operation of the tool
could create an explosion and fire when exposed to
flammable liquids or gases.
11. Check the blade carefully for cracks or damage
before operation.
ENF002-2
Replace cracked or damaged blade immediately.
12. Use only flanges specified for this tool.
13. Be careful not to damage the arbor, flanges
(especially the installing surface) or bolt. Dam-
age to these parts could result in blade breakage.
14. Make sure that the turn base is properly secured
so it will not move during operation.
GEA010-1
15. For your safety, remove the chips, small pieces,
etc. from the table top before operation.
16. Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
17. Make sure the shaft lock is released before the
switch is turned on.
18. Be sure that the blade does not contact the turn
base in the lowest position.
19. Hold the handle firmly. Be aware that the saw
ENB034-6
moves up or down slightly during start-up and
stopping.
20. Make sure the blade is not contacting the work-
piece before the switch is turned on.
21. Before using the tool on an actual workpiece, let
it run for a while. Watch for vibration or wobbling
that could indicate poor installation or a poorly
balanced blade.
22. Wait until the blade attains full speed before cut-
ting.
23. Stop operation immediately if you notice any-
thing abnormal.
24. Do not attempt to lock the trigger in the on posi-
tion.
25. Be alert at all times, especially during repetitive,
monotonous operations. Don't be lulled into a
false sense of security. Blades are extremely
unforgiving.
168 mm
120 mm
/II
17