Playing A Usb Device; Listening To The Radio - Pioneer SC-LX83 Guide Rapide

04 Basic playback

Playing a USB device

It is possible to play files
front of this receiver.
1 Switch the receiver into standby then connect your
USB device to the USB terminal on the front panel of
this receiver.
TUNER EDIT BAND AUTO SURR/ALC/ HOME
STREAM DIRECT THX
HDMI 5
VIDEO CAMERA
2 Switch on the receiver and your TV.
3 Press iPod USB on the remote control to switch the
receiver to the iPod/USB.
Use / to select 'Music' from the USB Top menu.
4
Use / and ENTER to select the track to be
5
played, then press the  PLAY button.
Basic playback controls
SC-LX83:
• Set the remote control operation selector switch to
SOURCE, then press iPod USB to switch the remote
control to the iPod/USB operation mode.
SOURCE
TV RECEIVER
CH VOL
TV CONTROL
INPUT MUTE
AUDIO
PARAMETER
TUNE
TOOLS
LIST
TOP MENU
BAND
PRESET ENTER
CATEGORY
HOME
MENU
TUNE
iPod CTRL PTY SEARCH
Note
1 • Compatible USB devices include external magnetic hard drives, portable flash memory drives (particularly key drives) and digital audio
players (MP3 players) of format FAT16/32.
• Pioneer cannot guarantee compatibility (operation and/or bus power) with all USB mass storage devices and assumes no responsibility for
any loss of data that may occur when connected to this receiver.
2 Make sure the receiver is in standby when disconnecting the USB device.
3 The iPod/USB function cannot be selected in the main zone when the Internet radio function is selected in the sub zone. Also, the iPod/USB
function cannot be selected in the sub zone when the Internet radio function is selected in the main zone.
36
En
1
using the USB interface on the
CONTROL ON/OFF
STANDARD ADVANCED STEREO MULTI-ZONE SPEAKERS
SURROUND SURROUND
iPod
iPhone
USB MCACC
SETUP MIC PHONES
USB mass
storage device
2
3
STATUS PHASE CTRL CH LEVEL
THX MPX PQLS MEMORY
VOL
AUTO/ALC/
STANDARD ADV SURR
DIRECT STEREO
PGM MENU
MUTE
SIGNAL SEL SLEEP DIMMER AUDIO
VIDEO
PARAMETER
A.ATT SBch MCACC INFO
DISP
T.EDIT
GUIDE
HDMI OUT
PRESET
CH
D.ACCESS CLASS
ENTER
RETURN
CLR
SC-LX73:
• Press iPod USB to switch the remote control to the
iPod/USB operation mode.
AUDIO VIDEO
PARAMETER PARAMETER
LIST TUNE TOOLS
TOP MENU T.EDIT
BAND GUIDE
PRESET ENTER PRESET
PTY
SEARCH RETURN
HOME
TUNE
MENU
iPod CTRL

Listening to the radio

1 SC-LX83 only: Set the remote control operation
selector switch to SOURCE.
2 Press TUNER to select the tuner.
3 Use BAND to change the band (FM or AM), if
necessary.
4 Tune to a station.
There are three ways to do this:
Automatic tuning – Press and hold TUNE / for
about a second. The receiver will start searching for
the next station.
Manual tuning – To change the frequency one step
at a time, press TUNE /.
High speed tuning – Press and hold TUNE / for
high speed tuning. Release the button at the
frequency you want.
Improving FM sound
If the TUNED or STEREO indicator doesn't light when
tuning to an FM station because the signal is weak, press
MPX to switch the receiver into mono reception mode.
Using the noise cut mode
The two noise cut modes can be used when receiving AM
broadcasts. Press MPX to select the noise cut mode (1 to
2).
Using Neural Surround
This feature uses Neural Surround™ technologies to
achieve optimal surround sound from FM radio.
• While listening to FM radio, press AUTO/ALC/
DIRECT for Neural Surround.
The Neural Surround mode can be selected also with
STANDARD.
DIRECT STEREO STANDARD ADV SURR
HDD DVD
THX PHASE CTRL STATUS
TV / DTV MPX PQLS
HDMI OUT AUDIO
1 2 3
SIGNAL SEL MCACC SLEEP INFO
4 5 6
DISP