Connecting To The Network Through Lan Interface; Plugging In The Receiver - Pioneer SC-LX83 Guide Rapide

Connecting your equipment
Connecting to the network through
LAN interface
By connecting this receiver to the network via the LAN
terminal, you can listen to Internet radio stations.
SC-LX83 only: When connected in this way, you can play
audio files stored on the components on the network,
including your computer, using HOME MEDIA GALLERY
2
inputs.
OUT 1 OUT 2 LAN ( 10/100 )
(CONTROL)
COAXIAL OPTICAL
ASSIGNABLE
IN 1 IN 2 IN 3 IN 1
MONITOR
(DVD) (CD) (CD-R) (TV/SAT)
OUT
VIDEO
CD-R/TAPE
DVR/BDR PHONO CD
IN IN
OUT IN OUT IN FRONT CENTER SURROUND
SUBWOOFER
SIGNAL
GND
B
FRONT HEIGHT/WIDE/ SURROUND BACK
R L R L (Single
KERS
TABLE
TRUCTION
L
TABLE
MODE
OI
PC
Connect the LAN terminal on this receiver to the LAN
terminal on your router (with or without the built-in DHCP
server function) with a straight LAN cable (CAT 5 or
higher).
Turn on the DHCP server function of your router. In case
your router does not have the built-in DHCP server
function, it is necessary to set up the network manually.
For details, see Network Setup menu on page 113.
LAN terminal specifications
LAN terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ethernet jack
Note
1 To listen to Internet radio stations, you must sign a contract with an ISP (Internet Service Provider) beforehand.
2 • Photo or video files cannot be played back.
• With Windows Media Player 11 or Windows Media Player 12, you can even play back copyrighted audio files on this receiver.
3 After this receiver is connected to an AC outlet, a 2 second to 10 second HDMI initialization process begins. You cannot carry out any
operations during this process. The HDMI indicator in the front panel display blinks during this process, and you can turn on this receiver
once it has stopped blinking. When you set the Control with HDMI to OFF, you can skip this process. For details about the Control with HDMI
feature, see Control with HDMI function on Operating Instructions in CD-ROM.
1
Internet
Modem
LAN
3 2 1 WAN
Router
LAN cable
(sold separately)
to LAN port
10BASE-T/100BASE-TX

Plugging in the receiver

Only plug in after you have connected all your
components to this receiver, including the speakers.
1 Plug the supplied power cord into the AC IN socket
on the back of the receiver.
2 Plug the other end into a power outlet.
CAUTION
• Handle the power cord by the plug part. Do not pull
out the plug by tugging the cord, and never touch the
power cord when your hands are wet, as this could
cause a short circuit or electric shock. Do not place
the unit, a piece of furniture, or other object on the
power cord or pinch the cord in any other way. Never
make a knot in the cord or tie it with other cables. The
power cords should be routed so that they are not
likely to be stepped on. A damaged power cord can
cause a fire or give you an electric shock. Check the
power cord once in a while. If you find it damaged,
ask your nearest Pioneer authorized independent
service company for a replacement.
• Do not use any power cord other than the one
supplied with this unit.
• Do not use the supplied power cord for any purpose
other than that described below.
• The receiver should be disconnected by removing the
mains plug from the wall socket when not in regular
use, e.g., when on vacation.
• Make sure the blue  STANDBY/ON light has gone
out before unplugging.
• If you have connected speakers with a 6
impedance, change the impedance setting before
turning on the power.
02
3
Ω
29
En