Publicité
Les langues disponibles
Les langues disponibles
3.3
"PROGRAMS" SETTING
The use of Programs allows the operator to work in "automatic" mode,
i.e., with the possibility to save and/or recall a configuration of set
parameters. Each baking programme can store up to three baking stages.
In the SMART BAKING mode, each baking stage stores 1 temperature,
1 time and 2 power percentages to memory, while in DUALT TEMP
mode, it saves 2 temperatures and 1 time. Each programme can also be
associated to a DELTA POWER configuration (see 3.5.8) other than
the one used in MANUAL mode.
The presence of a program running is shown in the "status bar", from
the name of the program itself.
To manage the Programs, open the dedicated menu. Press "MENU",
select PROGRAMS with the "SELECTION" (↑ and ↓) keys and then
"OK" to open the submenu.
Scroll through the list on the display using the "SELECTION " keys to
select the following items.
-
"Recent": a list of the last programs used
-
"Manual": ends program execution and switches to manual mode
-
"Pre-Heating": displays the setting screens of the pre-heating
program.
-
"Name search": orders the programs starting from the
selected letter
-
"Insert new": starts the procedure to create a program
-
"Modify": starts the procedure for editing an existing program.
-
"Delete": starts the procedure to eliminate an existing program
-
"USB Import": starts the procedure to import programs from a
external usb device to internal oven memory
-
"USB Export": starts the procedure to copy programs from the
internal oven memory to an external USB device
•
RECENT
Function to list the last programs used. Select the required program with
the "SELECT" keys and then press "OK" to run it and start the
heating/baking stage with the parameters of the chosen program.
•
MANUAL
Function to end program execution and switches to manual mode.
NOTE:
The same result is obtained in the main screen by
putting the oven in STOP and moving a baking parameters.
•
PRE-HEATING
This is the program dedicated to the heating of the oven that allows the
oven to be powered up with settings different from the baking ones.
When the heating temperature set is reached or pre-heating time expired,
the oven automatically loads the baking parameters. Use this function
when you need to:
- reduce the temperature increase time (by setting percentages higher
than the baking ones);
- program a slow temperature increase (by setting percentages lower than
the baking ones);
- program a discontinuous temperature increase (by setting a lower
heating temperature and percentages higher than the baking ones or vice-
versa);
- program a temperature increase for a pre-fixed time (by setting
temperature, percentages and pre-heating time).
In the "Pre-Heating" menu, select:
- "Enable" to activate the heating program
- "Settings" to access the setting screens containing the parameters of the
pre-heating program: in the first screen adjust the temperature (the
temperatures to be adjusted are two if using the DUAL TEMP mode)
then follows screen for adjusting the power percentages (screen not
available in DUAL TEMP), finally adjust pre-heating time (set //:// to
end pre-heating when the set temperature is reached).
- "Enable with Start", setting to use if the user wishes to tie the "Pre-
Heating" program to the pressing of the START button. In other words,
with this setting enabled, pressing the START button allows the user to
enable the heating program, while pressing the button again disables the
heating program and so on.
When the "Pre-Heating" program is enabled, the display turns orange.
•
NAME SEARCH
This is the function that lists all of the programs in the memory, in
alphabetical order, starting with the letter chosen with the
"SELECTION" key and confirmed with "OK". Select the program
required with the "SELECTION" keys, followed by "OK" to run the
program. Start the heating/baking stage with the chosen program
parameters.
•
INSERT NEW
The first screen for the program insert procedure required the name of
the program to be entered (fig. 20a). A flashing cursor in the top of the
display will indicate that the first letter of the name needs to be entered.
Select the required letter with the "SELECTION" keys and then press
"OK" to confirm and pass onto the next character. etc. Should it be
necessary to delete the last letter entered, scroll through the list to DEL
and then press "OK" or press the "DELETE" key. To complete the
name entry and pass on to the next screen, scroll through the list to END
and then press "OK" or press the "END" key. This will open the second
programming screen, which will ask for the number of stages in the
programme. Use the "SELECTION" keys to set the required number,
between 1, 2 or 3 (fig. 20b). This is followed by entering the working
temperature ("Temperature step 1") and the baking time ("Time step
1") (which will be preloaded to T1) (fig. 20c). Change the parameters
with the "+" and "-" keys, if the user wishes to set an endless program
for the "gradual temperature drop baking" mode, the time must be set
to //://, and then press "OK" to confirm. This will open the third
programming screen, where it is necessary to enter the power level for
the ceiling ("("Ceiling power step 1")") and floor ("Deck power step
1") (fig. 20d). Change the parameters with the "+" and "-" keys and
then press "OK" to confirm.
Programming continues with the screens for programming the second
and third stages, if present (fig. 20e-f-g-h).
Only those models with a steamer used at every stage in baking can
have an associated steam function at the start of the relevant baking
stage. The steam function will have the duration preset in 3.4. To enable
steaming, press the HOTKEY when the temperature setting screen is
shown, as indicated by the wording on the display: the special icon will
appear to the left of the temperature.
WARNING!
wording offering the choice to switch the steam function on/off
using the HOTKEY, increase the baking time for the previous stage
since after generating the steam, the boiler will cool down and will
need a certain amount of time to heat up and generate more steam.
Go back to the previous screens by pressing the "RETURN" key
one or more times.
NOTE:
If the oven is fitted with steamer and there are no
screens to program this, contact the Assistance Service to enable the
function.
Programming continues with the DELTA POWER function setting (fig.
20i): leave the // symbols to use manual settings (see 3.5.8) or use the +
and/or – keys to select the required balance.
The last screen shows a summary of the program created (fig. 20l). Press
OK to save and run the program. Press "RETURN" to go back to the
previous screens without saving.
NOTE:
When entering a DUAL TEMP programme, select the
mode as described in 3.2.3 before starting to enter a new programme.
The
procedure
described
programming.
•
MODIFY
Select the first letter of the program to be deleted with the "SELECTION"
keys, then press "OK" to put all of the programs in alphabetical order,
beginning with the chosen letter. Select the required program with the
"SELECTION" keys then press "OK" to open the edit screens. The
parameter edit procedure is the same as the procedure described above in
the "INSERT NEW" paragraph.
•
DELETE
Select the first letter of the program to be deleted with the "SELECTION"
keys, then press "OK" to put all of the programs in alphabetical order,
beginning with the chosen letter. Select the required program with the
"SELECTION" keys and then press "OK". Confirm deletion with "OK"
or cancel the operation by pressing "RETURN" several times.
•
USB IMPORT
Insert the USB device into the slot on the right side of the appliance after
removing the plug. The display will show a list of the directories in the
USB device. The <ROOT> item shows the first level of the file system.
Select the directory where the programs to be imported reside using the
"SELECTION" keys. The "+" and "-" keys enter and exit the selected
directory. Press "OK" to perform the import operation. A message will
show the number of the program correctly copied from the USB memory
to the oven memory. Remove the USB device and refit the previously
removed plug.
NOTE:
the <NO DIRECTORY> message means that there is no
USB or that it has not been correctly inserted into the slot.
•
USB EXPORT
UK/7
If the programming screen does not show the
here
above
remains
valid
for
Publicité
