ROBBE Charterle Notice De Montage page 7

Parts List for the basic fuselage structure
Part Description
No.
R 1 Fuselage side
R  Wing saddle
R 3 - R 6 Fuselage longeron
R 7 Fuselage former
R 8 / R 8a Undercarriage retainer plate
R 9 Fuselage former
R 10 Servo plate
R 11 Fuselage former
R 1 Fuselage former
R 13 Fuselage former
R 14 Motor mount
R 15 Motor bulkhead
R 16 In-fill block
R 17 Fuselage nose former
R 18 Wing retainer plate
R 18a Wing retainer plate doubler
R 19 Reinforcement
R 0 Fuselage former
R 1 Fuselage former
R  Fuselage turtle deck sheeting
R 3 Fuselage turtle deck sheeting
R 4 Fuselage bottom sheeting
R 5 Fuselage bottom sheeting
R 6 Fuselage bottom sheeting
R 7 Fuselage bottom sheeting
R 8 Windscreen frame
R 9 Fuselage nose sheeting
R 30 Fuselage hatch
R31 Hatch reinforcement
R 3 Pushrod support
R33 Tailskid
R 34 Battery hatch latch
The basic fuselage structure
Note: take care to prepare one right and one left fuselage
side R 1 (mirror-image pair).
Use cyano for all joints unless stated otherwise.
Fig. 31
- Glue the wing saddles R  and the longerons R 3 to R 6
to the fuselage sides R 1.
Assembly and operating instructions
Charterle
Laser-cut
sheet
Sheet B + D
Sheet C
Sheet E
Sheet C
Sheet F
Sheet C
Sheet C
Sheet C
Sheet C
Sheet C
Sheet C
Sheet C
Sheet E
Sheet E
Sheet C
Sheet C
Sheet C
Sheet C
Sheet C
Sheet D
Sheet D
Sheet B
Sheet B
Sheet B
Sheet D
Sheet D
Sheet D
Sheet B
Sheet C
Sheet C
Sheet C
Plastic
Figs. 32 and 33
- Slot together the formers R 7, R 8, R 9, R 11 and R 1 with
the servo plate R 10, and glue this assembly to one fuse-
lage side.
- Note that part R 8a is fitted later.
Material, dimensions No. off
Balsa,  mm  off
Poplar, 3 mm  off
Balsa, 4 mm  each
Poplar, 3 mm 1 off
Plywood,  mm 1 each
Poplar, 3 mm 1 off
Poplar, 3 mm 1 off
Poplar, 3 mm 1 off
Poplar, 3 mm 1 off
Poplar, 3 mm 1 off
Poplar, 3 mm  off
Poplar, 3 mm 1 off
Balsa, 4 mm  off
Balsa, 4 mm 1 off
Poplar, 3 mm 1 off
Poplar, 3 mm 1 off
Poplar, 3 mm  off
Poplar, 3 mm 1 off
Poplar, 3 mm 1 off
Balsa,  mm 1 off
Balsa,  mm 1 off
Balsa,  mm 1 off
Balsa,  mm 1 off
Balsa,  mm 1 off
Balsa,  mm 1 off
Balsa,  mm 1 off
Balsa,  mm 1 off
Balsa,  mm 1 off
Poplar, 3 mm  off
Poplar, 3 mm 1 off
Poplar, 3 mm 1 off
Ready made 1 off
7
Fig. 34
- Fit the second fuselage side R 1 on the structure, and
check that the fuselage sides line up flush at the tail end.
- Glue the second fuselage side to the former framework.
No.
3279