Bosch Professional GCM 18V-305 GDC Notice Originale page 22

22 | English
Assembly
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Items Included
See the list of items included at the start of
the operating manual.
Check to ensure that all the parts listed below have been
supplied before using the power tool for the first time:
– Sliding mitre saw with fitted saw blade (44)
– Locking knob (12)
– Hex key (17)
– Hex key (18)
– Screw clamp (19)
– SDS bolt (23)
– Dust bag
Note: Check the power tool for possible damage.
Before continuing to use the power tool, carefully check that
all protective devices or slightly damaged parts are working
perfectly and according to specifications. Check that the
moving parts are working perfectly and without jamming;
check whether any parts are damaged. All parts must be fit-
ted correctly and all the conditions necessary to ensure
smooth operation must be met.
If the protective devices or any parts become damaged, you
must have them properly repaired or replaced by an author-
ised service centre.
Extra tools required (not included in the delivery):
– Cross-headed screwdriver
– Open-ended spanner (size: 8 mm)
– Ring spanner, open-ended spanner or socket spanner
(sizes: 10 mm and 17 mm)
Activating the Bluetooth® Low Energy
Module GCY 42
Read the corresponding operating instructions for informa-
tion about the Bluetooth® Low Energy Module GCY 42.
Activating the Button Cell
– Remove the cover for the Bluetooth® Low Energy Module
GCY 42 (31).
– Remove the insulation between the button cell and the
Bluetooth® Low Energy Module GCY 42.
– Close the cover (31) to prevent dirt from getting in.
Remove the cover for the Bluetooth® Low Energy Mod-
u
ule GCY 42 on the power tool, e.g. using a screwdriver
or a large coin. Using unsuitable objects can damage the
electronics or the cover.
1 609 92A 6TT | (19.07.2021)
Battery Charging
Use only the chargers listed in the technical data. Only
u
these chargers are matched to the lithium-ion battery of
your power tool.
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
Do not continue to press the On/Off switch after the
u
power tool has automatically switched off. The battery
can be damaged.
Follow the instructions on correct disposal.
Removing the Battery
The battery (32) is equipped with two locking levels to pre-
vent the battery from falling out if the battery release
button (33) is pressed unintentionally. The battery is held in
place by a spring when fitted in the power tool.
To remove the battery , press the release button and pull the
battery out of the power tool. Do not use force to do this.
Battery charge indicator
The green LEDs on the battery charge indicator indicate the
state of charge of the battery. For safety reasons, it is only
possible to check the state of charge when the power tool is
not in operation.
Press the button for the battery charge indicator or
show the state of charge. This is also possible when the bat-
tery is removed.
If no LED lights up after pressing the button for the battery
charge indicator, then the battery is defective and must be
replaced.
Note: The state of charge of the battery is also displayed on
the user interface (3).
Battery model GBA 18V...
LEDs
3× continuous green light
2× continuous green light
1× continuous green light
1× flashing green light
to
Capacity
60−100 %
30−60 %
5−30 %
0−5 %
Bosch Power Tools