Specific Safety Rules - Milwaukee M4910-21 Manuel D'utilisation

follow the manufacturer's instructions for turning off
the unit and relieving the pressure before removing the
spray tip to clean.
 Do not leave the unit energized or under pressure while
unattended. When the unit is not in use, turn off the
unit and relieve the pressure in accordance with the
manufacturer's instructions.
 High pressure spray is able to inject toxins into the
body and cause serious bodily injury. In the event that
injection occurs, seek medical attention immediately.
 Check hoses and parts for signs of damage. Replace
any damaged hoses or parts.
 This system is capable of producing 3000 psi. Only use
replacement parts or accessories that are specified by
the manufacturer and are rated a minimum of 3200 psi.
 Always engage the trigger lock when not spraying.
Verify the trigger lock is functioning properly.
 Verify that all connections are secure before operating
the unit.
 Keep guards in place and in working order. Never
operate the tool with any guard or cover removed. Make
sure all guards are operating properly before each use.
 To reduce the risk of injury, keep children and visitors
away. All visitors should wear safety glasses and be kept
a safe distance from work area.
 Keep the area of operation clear of all persons,
particularly small children, and pets.
 Use right tool. Don't force tool or attachment to do a
job it was not designed for. Don't use it for a purpose not
intended.
 Do not operate the equipment while barefoot or when
wearing sandals or similar lightweight footwear. Wear
protective footwear that will protect your feet and improve
your footing on slippery surfaces.
 Exercise caution to avoid slipping or falling.
 Always wear eye protection with side shields marked
to comply with ANSI Z87.1. Failure to do so could result
in fluids entering your eyes resulting in possible serious
injury.
 Use only recommended accessories. The use of im-
proper accessories may cause risk of injury.
 Follow the maintenance instructions specified in this
manual.
 Check damaged parts. Before further use of the tool, a
guard or other part that is damaged should be carefully
checked to determine that it will operate properly and
perform its intended function. Check for alignment of
IMPORTANT SAFETY INSTRUCTIONS

SPECIFIC SAFETY RULES

 Know how to stop the unit and bleed pressure quickly.
Be thoroughly familiar with the controls.
WARNING: To reduce the risk of injury:
 Always wear appropriate gloves, eye protection
marked to comply with ANSI Z87.1, and a respirator
or mask when painting.
 Do not operate or spray near children. Keep children
away from equipment at all times.
 Do not overreach or stand on an unstable support.
Keep effective footing and balance at all times.
 Stay alert and watch what you are doing.
 Do not operate the unit when fatigued or under the
influence of drugs or alcohol.
 Do not kink or overbend the hose.
 Do not expose the hoses to temperatures or to
pressures in excess of those specified by the
manufacturer.
 Do not use the hose as a strength member to pull or
lift the equipment.
moving parts, binding of moving parts, breakage of parts,
mounting, and any other conditions that may affect its
operation. A guard or other part that is damaged must
be properly repaired or replaced by an authorized service
center to avoid risk of personal injury.
 Never leave tool running unattended. Turn power off.
Don't leave tool until it comes to a complete stop.
 Follow manufacturer's recommendations for safe
loading, unloading, transport, and storage of
machine.
 Be thoroughly familiar with controls. Know how to stop
the product and bleed pressure quickly.
 Keep tool dry, clean, and free from oil and grease.
Always use a clean cloth when cleaning. Never use brake
fluids, gasoline, petroleum-based products, or any sol-
vents to clean tool.
 Do not use tool if switch does not turn it off. Have de-
fective switches replaced by an authorized service center.
 Before cleaning, repairing, or inspecting, shut off the
motor, release pressure, and make certain all moving parts
have stopped.
 Avoid dangerous environment. Don't use in damp or
wet locations or expose to rain. Keep work area well
lit.
 Never direct a paint stream toward people or pets,
or any electrical device.
 Never start the machine if ice has formed in any part
of the equipment.
4 — English