Niko 350-20063 Mode D'emploi page 12

350-20063
7. TROuBLESHOOTING
Problem Cause
The calibration was not - Insufficient daylight (or not
successful: the red indication LED
keeps flashing.
- Too much daylight, which
- There are not enough variations
- The daylight level was varying
An error occurred while setting - Insufficient daylight (or not
the first reference point: the red
indication LED is flashing briefly
and then stays lit. - The daylight level was varying
An error occurred while setting - Insufficient daylight (or not
the second reference point: the
red indication LED is flashing
briefly and the blue indication LED - The two reference points are
then stays lit.
- The difference between the arti-
- The daylight level was varying
8. MAINTENANCE
Dirt may prevent the presence detector from functioning properly. Therefore, always keep the lens clean and
dry. Use a damp cloth and water with some detergent to clean the lens. Never exert pressure to wipe the lens
clean. If the lens or other parts of the presence detector are defective, please contact an authorised installer.
9. TECHNICAL DATA
dimensions
power supply voltage
stand-by consumption
relay contact
maximum load
maximum switching capacity
maximum inrush current
channel 1
light sensitivity
switch-off delay
light level of the orientation lighting
duration of the orientation lighting
mounting height (fig. 9)
detection range (fig. 9)
protection degree
protection class
ambient temperature
quality mark
accessories
12
EN nv Niko sa
Solution
- Press
enough daylight is registered by
calibration.
the sensor).
- Press
means the sensor is saturated.
is locked and returns to the
factory settings.
in the artificial light level (or the
variations are not adequately
registered by the sensor).
too much during calibration.
- Press
enough daylight is registered by
reference point.
the sensor).
- Press
is locked and returns to the
too much while setting.
factory settings.
- Press
enough daylight is registered by
reference point.
the sensor).
- Press
is locked and returns to the
identical.
factory settings.
ficial light level in both reference
points is too small.
too much while setting.
59 x 127 mm (HxW)
230 Vac ± 10%, 50 Hz
0.2 W (without lighting fixtures)
NO (max. 10 A), light- and motion-sensitive
incandescent lamps (2300 W)
230 V halogen lamps (2300 W)
all low-voltage halogen lamps (500 VA)
fluorescent lamps (non-compensated) (1200 VA)
economy lamps (CFLi) (1200 VA)
140 μF
165 A/20 ms
1 – 10 V/max. 10 mA
50 – 1500 lux
1 – 60 min
5 – 100%
0 – 60 min, infinite
2.5 – 4 m
circular, 3 – 20 m
IP20
class I devices
-5 – +50°C
CE marked in compliance with EN 60669-2-1
IR remote control (350-20064)
Industriepark West 40, BE-9100 Sint-Niklaas, Belgium — tel. +32 3 778 90 00 — fax +32 3 777 71 20 — e-mail: support@niko.be — www.niko.eu
10. WARNINGS REGARDING INSTALLATION
- The installation should be carried out by a registered installer and in compliance with the statutory
regulations.
- This manual should be presented to the user. It should be included in the electrical installation file, and it
and repeat the
should be passed on to any new owners. Additional copies are available on the Niko website or via the Niko
support service. The latest manual for this product is available on the Niko website at any time.
- During installation, the following should be taken into account (non-exhaustive list):
once. The sensor
- the statutory laws, standards and regulations.
- the technology currently available at the time of installation.
- this manual, which only states general regulations and should therefore be read within the scope of
each specific installation.
- the rules of proper workmanship.
This product complies with all of the relevant European guidelines and regulations. If applicable, you can find
or to reset the
the EC declaration of conformity regarding this product at www.niko.eu.
once. The sensor
11. NIkO SuPPORT
In case of doubt or for the specific exchange procedure in case of a possible defect, contact the Niko support
service in Belgium at +32 3 778 90 80 or your wholesaler/installer. Contact details and more information can
be found at www.niko.eu under the "Help and advice" section.
or to reset the
12. GuARANTEE PROVISIONS
once. The sensor
- The period of guarantee is four years from the date of delivery. The delivery date is the invoice date of
purchase of the product by the consumer. If there is no invoice, the date of production applies.
- The consumer is obliged to inform Niko in writing about the non-conformity, within two months after stating
the defect.
- In case of a non-conformity, the consumer only has the right to a product repair or replacement free of
charge, which shall be decided by Niko.
- Niko shall not be held liable for a defect or damage resulting from incorrect installation, improper or
careless use, incorrect operation, transformation of the product, maintenance that does not adhere to the
maintenance instructions or an external cause, such as damage due to moisture or overvoltage.
- The compulsory regulations of the national legislation concerning the sale of consumer goods and the
protection of the consumer in the countries where Niko sells, directly or via sister companies, subsidiaries,
chain stores, distributors, agents or permanent sales representatives, take priority over the above-mentioned
rules and regulations.
PM350-20063R13315