Campingaz Plancha EX Plus Utilisation Et Entretien page 12

- the hose does not touch any components which may
get hot.
- That the cover is not in the closed position (depending
on the model)
- This device has a large number of vents to optimize the
device use. Be sure that these vents are not blocked.
h) LID (DEPENDING ON MODEL) – FIG. 3
PAGE 4.
On models equipped with an articulated lid, please note
that:
- The lid is a protective lid to be closed when the
appliance is not in use
- The lid must not be closed during the use of
the appliance. This could damage the paint and
overheat the handle.
i) LIGHTING THE BURNERS
In case of burn back (ignition under the burner
cap) switch the product off, allow it to cool down
(approximately five minutes), then reignite the
appliance. If the problem of burn back persists, then
please contact your local Campingaz
Read steps 1 to 5 before beginning with step 1.
1) Make sure that the control knobs are in the "OFF"
position (●).
2) Open the gas cylinder valve.
3) Push the adjustment lever down and turn it anticlockwise
until it is in the full flow position (
press the ignition button ( ) down until you hear a click.
Repeat 3 or 4 times if necessary.
4) If the device still does not light, place the control knob
in the "OFF" (●) position and wait 5 minutes before
starting the operation again.
5) When the first burner has been lighted, repeat the
operation for the second burner.
Important :
If the burner fails to light after the second attempt, turn
the control knob to the "off" position (●) and check that the
burner outlets and the venturi tube are not blocked.
j) LIGHTING THE BURNERS MANUALLY
If automatic ignition does not work, turn the control knob
to "OFF" (●).
Remove the cooking plate. Hold a lighted match next to
the burner, then push in the control knob and turn it to the
"HI" position ( ). Put the cooking plate back in place
with protective gloves, being sure to correctly position the
drippings evacuation hole.
k) EXTINGUISHING THE BURNERS
Return the control knobs to the "OFF" position (●), then
close the cylinder valve.
l) REPLACING THE GAS CYLINDER
- Always work in a well ventilated area and never in the
presence of a flame, spark or heat source.
- Return the control knobs in the "off" position (●) then
close the cylinder valve.
- Remove the regulator, check that the sealing joint is in
good condition.
- Put the full cylinder in place, refit the regulator,
taking care not to apply stress to the hose.
Check for gas leaks.
m) OPERATION
When used for the first time, heat up the appliance
(depending on model: remove the lid) with its burners
in full on position (
order to eliminate any odors resulting from the paint on
the new parts.
We recommend using protective gloves for handling
elements that are particularly hot. Use long-handled
utensils to manipulate food on the cooking plate.
Before cooking, preheat the device for a few minutes in
the "HI" position (
Cooking speed can be regulated via the adjustment
buttons: between the full flow position (
flow position (
Important : If one or several burners go out whilst you
are using the appliance, move the adjustment buttons
to "OFF" (●) immediately. Wait five minutes to allow the
unburned gas to escape. Only carry out the lighting steps
after this time.
Important : Allow the unit to cool off completely before
handling the cover (depending on the model).
representative.
®
n) CLEANING AND MAINTENANCE
Never modify the appliance: any modification may
prove dangerous.
- In order to maintain your appliance in perfect operating
condition, it is recommended to clean it periodically
), then immediately
(after 4 or 5 uses).
- Wait until the appliance has cooled down before
cleaning.
- Close the gas cylinder.
- The grill burner must be cleaned and checked every
3 months. Remove the entire burner and check that
no dirt or spider webs block the venturi tube openings,
which may cause the burner to be less efficient or cause
a dangerous gas fire outside the burner.
- Clean the top of the burner, as well as the sides and
base, using a moist sponge (water with washing up
liquid). If necessary, use a damp steel brush.
- Check that all burner outlets are clear and let dry before
using again. If necessary, use a wire brush to unclog the
burner outlets.
- Refit the grill burner correctly.
- Clean the orifices on the Venturi jet (see diagram below)
or the burner if necessary.
11
), for approximately 15 minutes in
).
).
Outlet holes
Venturi tube openings
) and medium
GB