Campingaz Plancha EX Plus Utilisation Et Entretien page 11

- slide the collars behind the two first bosses on the
tailpieces and tighten them until the tightening head
breaks.
- check for leaks following the instructions in
paragraph f).
2) To use the equipment with the flexible hose XP
D 36-112, G 1/2 and M 20x1.5 nuts: (section e) b))
- If need be, loosen and remove the NF ringed hose
connector to release the G1/2 inlet connector and
remove the seal.
- tighten the G 1/2 threaded nut on the hose onto the
appliance inlet connector and the M20x1.5 threaded
nut onto the regulator output connector following the
instructions supplied with the flexible hose.
- Use two wrenches to tighten the flexible hose on the gas
end piece:
► a number 14 wrench to immobilize the device input
connection,
► an adjustable wrench to tighten the flexible hose
nut.
GB
- use a wrench to immobilize the regulator output
connector.
- check for leaks following the instructions in paragraph f).
Check that the flexible hose stretches out normally
without twisting or pulling and does not come into contact
with the hot sides of the appliance. It should be replaced
when the expiry date on the hose is passed or whenever
it is damaged or develops surface cracks.
■
Belgium, Luxembourg, United Kingdom, Ireland,
Portugal, Spain, Italy, Croatia, Greece, Netherlands,
Czech Republic, Slovakia, Hungary, Slovenia,
Norway, Sweden, Denmark, Finland, Bulgaria,
Turkey, Romania, Poland, Estonia:
The appliance is equipped with a circular connector. It
should be used with flexible hose that is suitable for use
with butane and propane gas. Hose length should not
exceed 1.20 metre. It should be replaced if it is damaged
or cracked, when required by national regulations or at the
end of the part lifecycle. Do not pull or pierce the hose.
Keep hose away from any parts of the appliance that get
hot. Check that the flexible hose stretches out normally,
without twisting or pulling.
■
Switzerland:
The appliance should be used with flexible tubing that
is suitable for use with butane and propane gas. Hose
length should not exceed 1.50 metre. It should be
replaced if it is damaged or cracked, when required by
national regulations or at the end of the part lifecycle. Do
not pull or pierce the tubing. Keep away from any parts
of the appliance that get hot. Check that the flexible hose
stretches out normally, without twisting or pulling.
Flexible tubing connection: to connect the tubing to the
connector on the appliance, tighten the nut on the tubing
firmly but without excess force using the two wrenches
provided:
► no. 14 wrench to tighten the connector.
► no. 17 wrench to tighten the nut on the tubing
f) CHECKING FOR GAS LEAKS
1) Work outside, away from all sources of ignition.
Do not smoke.
2) Make sure the control knobs are in the "off" (●) position.
3) Connect the flexible tubing to the connector and
appliance as described in part e).
4) Fit the regulator onto the gas cylinder in accordance
with its instructions.
5) Use a gas leak solution to test for leaks. Important:
never use a naked flame to check for gas leaks.
6) Apply the solution to the connections cylinder/regulator/
hose/apparatus (the control knobs should remain
closed: off position (●)). Open the gas cylinder valve.
7) Bubbles in the gas leak solution indicate that there are
gas leaks.
8) The leak can be stopped by tightening any hose
connection or replacing any faulty component. The
appliance must not be used until the leak is stopped.
9) Close the valve on the gas cylinder.
Important :
Never use a flame to detect a gas leak.
Check for leaks at least once per year and each time the gas
cylinder is replaced.
g) PRIOR TO USE
Never use the appliance until the instructions have been
read carefully and understood. Also, make certain that:
- there are no leaks
- the venturi tubes are not blocked (example:
spider webs)
10