Table des Matières
Publicité
Remote control
■ Battery installation
1
Open the battery cover.
2
Insert the batteries according to the terminal indicated in
the battery compartment. When inserting or removing the
batteries, push them toward the (–) battery terminals.
3
Close the cover.
Caution:
● Replace all old batteries with new ones at the same
time.
● Do not mix old and new batteries.
● Remove the batteries if the unit will not be used for a
long period of time. This will prevent potential damage
due to battery leakage.
● Do not use rechargeable batteries (nickel-cadmium
battery, etc.).
● Installing the batteries incorrectly may cause the unit
to malfunction.
● Batteries (battery pack or batteries installed) shall not
be exposed to excessive heat such as sunshine, fire
or the like.
Notes concerning use:
● Replace the batteries if the operating distance is re-
duced or if the operation becomes erratic. Purchase
2 "AAA" size batteries (UM/SUM-4, R03, HP-16 or
similar).
● Periodically clean the transmitter on the remote control
and the sensor on the unit with a soft cloth.
● Exposing the sensor on the unit to strong light may in-
terfere with operation. Change the lighting or the direc-
tion of the unit.
● Keep the remote control away from moisture, heat,
shock, and vibrations.
■ Test of the remote control
The remote control can be used within the range shown below:
Remote sensor
0.2 m - 6 m
(8" - 20')
All manuals and user guides at all-guides.com
General control
Press the ON/STANDBY button to turn the power on or off.
Press the DIMMER button (remote control).
If you turn off and on the main unit with the volume set to
27 or higher, the volume starts at 16 and fades in to the
last set level.
Turn the volume knob toward VOLUME +/– (main unit) or
press VOL +/– (remote control) to increase or decrease
the volume.
To mute the volume, press the
Press again to restore the volume.
When you press any of the following buttons, the unit turns on.
●
●
The main unit will enter the standby mode after approxi-
mately 15 minutes of inactivity during:
Audio In: No detection of input signal.
CD: In the stop mode or no disc.
USB: In the stop mode or no media.
When the power is first turned on, the unit is in the extra
bass mode. "X-BASS" indicator appears. To cancel this
mode, press the X-BASS button (remote control).
1
MICRO COMPONENT SYSTEM XL-LS701
2
Sound default settings : Bass = 0, Treble = 0, X-Bass = off
Press the FUNCTION button repeatedly to select desired
function.
Note:
The backup function will protect the memorised function
mode for a few hours should there be a power failure or
the AC power lead becomes disconnected.
E-5
■ To turn the power on
■ Display brightness control
(Display is dim).
Dimmer 1
(Display gets dimmer).
Dimmer 2
(Display is bright).
Dimmer off
■ Volume auto fade-in
■ Volume control
■ Muting
■ Direct key power on function
CD / , USB / , AUDIO IN, TUNER, OPEN/CLOSE
(remote control): Selected function is activated.
/ (main unit): The unit turns on and playback of the
last function will start (CD, USB, AUDIO IN, TUNER)
■ Auto power off function
■ X-Bass control
■ Bass or Treble control
Press the BASS or TREBLE button to select "Bass" or "Tre-
ble" respectively.
Within 5 seconds, press the VOL (+ or –) button to adjust the
bass or treble.
- 5 ↔ - 4 ........ ↔ + 4 ↔ + 5
Press SOUND (DEFAULT) button to return sound to
default settings. "SOUND DEFAULT" appears on the
display.
■ Function
CD
FM STEREO
AUDIO IN
button (remote control).
- 5 ↔ - 4 ........ ↔ + 4 ↔ + 5
FM MONO
USB
Publicité
Table des Matières
