B.5 Sliding Switches; B.5.1 Point Selection; B.5.2 Rounding Selection; B.5.4 Currency Conversion Mode And Tax Calculation Mode Selection - Olympia CPD 3212 S Mode D'emploi

Mt
Memory total key
- Recall / Clear memory contents.
M◊
Memory sub-total key
- Recall memory contents.
M _
Memory subtraction key
- The entered value is subtracted from the memory con-
tents.
- Conclude calculation.
The result is subtracted from the memory contents.
M+
Memory addition key
- The entered value is added to the memory contents.
- Conclude calculation.
The result is added to the memory contents.
Paper transport key
Percent mark-up key
%+
- The percentage value is added.
To be proceeded by stored percentage or entered percen-
tage.
∆
Delta %
- For the calculation of percentage differences of two va-
lues.
Calculation
COST SELL MARGIN
- Used for calculating the cost, selling price and profit mar-
gin amount.
Enter the value of any 2 items to obtain automatically the un-
known value item. (e.g. enter the value of the cost and the
selling price to obtain automatically the profit margin %.)
Rate set key
RATE
To perform with function key and numeral key.
- Recall and set the 1st currency and 2nd currency.
- Recall and store the currency rates.
- Recall the stored rate and store the rate for TAX and %+
calculations.
- Negative value can not be entered as any rate.
5 1
Currency conversion-1 / Tax plus key
TAX+ Selection slide switch at the CONV mode position:
- Convert from 2nd currency to 1st currency.
To be proceeded by conversion rates of originally installed
11-currency and user stored currencies.
Selection slide switch at the TAX mode position:
- The Tax value is added.
To be proceeded by stored tax rate.
5 2
Currency conversion-2 / Tax minus key
TAX– Selection slide switch at the CONV mode position:
- Convert from 1st currency to 2nd currency.
To be proceeded by conversion rates of originally installed
11-currency and user stored currencies.
Selection slide switch at the TAX mode position:
- The Tax value is subtracted.
To be proceeded by stored tax rate.
8

B.5 Sliding switches

B.5.1 Point selection

A F 0 2 3 4 6 Floating decimal point ON
Result to maximum number of decimal places.
A F 0 2 3 4 6 A F 0 2 3 4 6
The result is given, depending on the switch setting, to 0,2,3,4 or 6
decimal places.
Sums which extend beyond the number of places to the left of the
decimal point, limited by a fix point, results in the decimal places
being truncated.
A F 0 2 3 4 6 Rapid adding ON (add mode)
After entering the digits (without point) and pressing the Addition or
Subtraction keys, the decimal point is automatically set in front of
the last two digits.
At Conversion-Mode:
If conversion result is Euro, the decimal point will be automatically
set at 2 & 5/4, excluding the case of decimal setting at F position.

B.5.2 Rounding selection

M 5/4 L
Truncation ON
The decimal places extending beyond the set number are trunca-
ted.
M 5/4 L
Rounding ON
The decimal number extending beyond the set number of places is
rounded up or down.
M 5/4 L
General rounding to 1 digit
B.5.3 Calculation mode and item counter selection
D P IC Display mode
D P IC Print and Display mode
D P IC Item counter (+),ON
- Counts all + and - entries, upwards
When switching from D to P or IC, a control paper feeding of 1 line
is executed.
B.5.4 Currency conversion mode and Tax calculation mode
selection
CONV TAX Currency conversion mode
CONV TAX Tax calculation mode
B.6 Display indication
M - The memory contains data
– - Negative value
E - Capacity overflow
Currency symbols on display are shown in "Currency code table"
(page 29)
When depressing RATE SEt will be appeared on display.
When Tax rate is stored or recalled, t will be appeared with num-
ber on display.
When %+ rate is stored or recalled, P will be appeared with num-
ber on display.
Fixed point ON