Alesis MULTIMIX 16 USB FX Guide D'utilisation page 7

TOP PANEL FEATURES
11 11
12 12
13 13
14 14
16 16
26 26
25 25
24 24
23 23
28 28
29 29
27 27
21 21
19 19
20 20
18 18
17 17
1. POWER LED – Illuminates when the MultiMix 16 USB FX is on.
2. PHANTOM POWER LED – Illuminates when phantom power is engaged.
3. MAIN OUT – Use standard 1/4" cables to connect this output to the house speaker or amplifier system. The
level of this output is controlled by the MAIN VOLUME knob.
4. MONITOR OUT – Use standard 1/4" cables to connect this output to your monitor speaker or amplifier system.
The level of this output is controlled by the MONITOR VOLUME knob.
5. PHONES – Connect your 1/4" headphones to this output. The PHONES knob controls volume.
6. FX SEND – You may connect the input of an external device (usually an outboard effects device) to this output
with a 1/4" mono cable. This output can also be used to create a custom monitor mix for onstage musicians.
You can adjust the level with the AUX PRE SEND knob.
7. AUX SEND – You may connect the input of an external device (usually an outboard effects device) to this
output with a 1/4" mono cable. This output can also be used to create a custom monitor mix for onstage
musicians. You can adjust the level with the AUX PRE knob.
8. AUX RETURN INPUTS – You may connect the outputs of an external device to these inputs with 1/4" mono
cables. This is usually used for outboard effects devices but can also be used like an extra input channel for
synthesizers, drum machines, etc. If your source is mono, plug it into the left jack and it will be heard on both
the left and right sides.
9. 2 TRACK INPUTS – You may connect the outputs of an external recording device to these inputs using
standard RCA cables. This can be used to listen to a 2-track recording you've just made, or to connect to a
personal media player to play pre-recorded music before your live gig. Press the 2 TRKS/USB TO MONITOR
button to hear this in your headphones or monitor speakers. Press the 2 TRKS/USB TO MAIN to hear this in
the house speakers.
10. 2 TRACK OUTPUTS – You may connect an external recording device to these outputs using standard RCA
cables.
11. MIC INPUT – Connect a microphone to these inputs with an XLR
cable.
12. LINE INPUT – Connect line-level devices to these inputs with 1/4"
cables.
13. INSERT – The insert jack allows you to insert a compressor, EQ, or
any other signal processor in between the MultiMix 16 USB FX's
preamplifier and A/D converter. Use a standard 1/4" TRS cable
when connecting a device to this insert.
14. LO CUT SWITCH – When this button is depressed, the channel's
high-pass filter will engage, reducing frequencies below 80 Hz to
reduce any low-level noise.
11 11 11 11 11 11
11 11
12 12 12 12 12 12 12 12
13 13 13 13 13 13 13 13
14 14 14 14 14 14
14 14
16 16 16 16 16 16 16 16
26 26 26 26 26 26
26 26
25 25 25 25 25 25
24 24 24 24 24 24
24 24
23 23 23 23
23 23 23 23
28 28 28 28 28 28 28 28
29 29 29 29 29 29 29 29
27 27 27 27 27 27 27 27
21 21 21 21 21 21 21 21
19 19 19 19 19 19 19 19 19 19
20 20
20 20
20 20 20 20
18 18 18 18 18 18 18 18 18 18
17 17 17 17 17 17 17 17
8
11 11 11 11 11 11
8
12 12 12 12 12 12
11 11
13 13 13 13 13 13
11 11
14 14 14 14 14 14
16 16 16 16 16 16
34 34
15 15
26 26 26 26
26 26
26 26
24 24 24 24 24 24
23 23 23 23 23 23 23 23
28 28 28 28 28 28 28 28
29 29 29 29 29 29 29 29
27 27
27 27 27 27 27 27
21 21 21 21 21 21 22 22
19 19 19 19 19 19 19 19
20 20
20 20 20 20 20 20
18 18 18 18 18 18 18 18
17 17 17 17 17 17 17 17
7
6 4 3
9 10 10
7 4 3
11 11 11 11 11 11 5
11 11 11 11 11 11 39 39
36 36
30 30
38 38
35 35
26 26 26 26 26 26 32 32
23 23 23 23 31 31
23 23
28 28 28 28 28 28 28 28
29 29 29 29 29 29
27 27 26 26
27 27 27 27
2
1
22 22 22 22 22 22
33 33
19 19 19 19
20 20
20 20 20 20
18 18 18 18
17 17 17 17 17 17 37 37
When using LINE INPUTS 9-16 and
the AUX RETURNS:
• If only the left channel is used, the
signal will be heard in both left and
right channels and the balance will
not be adjustable.
• If only the right channel is used,
the signal will be heard in the right
channel only.