Fm/Am Tuning; Tuning In To The Desired Fm/Am Station (Frequency Tuning); Registering Fm/Am Stations And Tuning In (Preset Tuning) - Yamaha RX-V1065 Mode D'emploi

The FM/AM tuner of this unit provides the following two
modes for tuning.
■
Frequency tuning mode
You can tune in to a desired FM/AM station by searching
or specifying its frequency.
■
Preset tuning mode
You can preset the frequencies of FM/AM stations by
registering them to specific numbers, and later just select
those numbers to tune in.
Note
• Adjust the FM/AM antennas connected to this unit for the best reception.
Tuning in to the desired FM/AM station
(Frequency tuning)
1
Rotate the RINPUT selector (or press
dTUNER) to select "TUNER" as the input
source.
2
Press GFM (eFM) or GAM (eAM) to select
a band.
"FM" or "AM" appears on the front panel display
according to the band that you have selected.
3
Press HTUNING l / h (or eTUNING k /
n) to specify the frequency.
To adjust the frequency to a higher range, press h (or
k). To adjust it to the lower range, press l (or n).
The TUNED indicator on the front panel display
lights up when the tuner is tuned in to a station. The
STEREO indicator also lights up if the program being
broadcasted is in stereo.
FM 92.5 MHz
The frequency changes in the following manner according
to how you press HTUNING l / h (or eTUNING
k / n).
When you press the key more than 1 second
The tuner searches the frequency of a station that is
detectable around the current frequency. This is effective
when the tuner can receive strong signals without any
interference. Once the search starts, release the key.
When you keep holding the key, the search continues even
when a station is detected. This is useful when you want to
tune in to a specific station.
When you press and release the key
The tuner increases or decreases the frequency in steps.
Use this method when the tuner cannot receive strong
signals and stations are skipped during the search.
y
• You can switch between stereo and monaural for FM broadcast in the
Option menu (page 38).
30
En

FM/AM tuning

STEREO
TUNED
4
To tune in by direct frequency tuning, press
lNumeric keys to enter the frequency of
the station.
Enter only integers. For example, if you want to set
the frequency to 88.9 MHz, enter "889".
Notes
• When you press lNumeric keys during preset tuning, a
preset number is selected. Set tuning mode to frequency tuning
mode using HTUNING/CH l / h (or eTUN./CH k / n)
prior to the operation.
• "Wrong Station!" appears on the front panel display when you
enter a frequency that is out of receivable range. Make sure that the
entered frequency is correct.
Registering FM/AM stations and
tuning in (Preset tuning)
You can register up to 40 FM/AM stations (Preset).
Registering stations by automatic station
preset
The tuner automatically detects FM stations with strong
signals and registers up to 40 stations. To register AM
stations, use manual station preset.
1
Rotate the RINPUT selector (or press
dTUNER) to select "TUNER" as the input
source.
2
Press rOPTION on the remote control.
The Option menu for "TUNER" is displayed
(page 37).
3
Select "Auto Preset" and then press
jENTER.
Auto Preset
Automatic station preset starts about 5 seconds later
from the lowest frequency upwards.
y
• You can select the preset number at which the preset starts by
pressing ePRESET k / n or jCursor k / n while "READY"
is displayed on the front panel display.
• To cancel registration, press jRETURN.
Status
01:FM 87.5 MHz
Preset number
During the automatic station preset, "MEMORY"
appears in the front panel display each time a station
is registered.
Frequency