Roland RD-700SX Mode D'emploi page 160

Implémentation MIDI
❍Panpot (Controller number 10)
Status 2nd byte
BnH 0AH
n = MIDI channel number:
vv = Panpot:
* These messages are transmitted when Pan value is set in EXTERNAL Zone.
❍Hold 1 (Controller number 64)
Status 2nd byte
BnH 40H
n = MIDI channel number:
vv = Control value:
* These messages are transmitted when Damper pedal is operated.
❍Portamento (Controller number 65)
Status 2nd byte
BnH 41H
n = MIDI channel number:
vv = Control value:
* These messages are transmitted when Portament Swicth is set in EXTERNAL Zone.
❍Sostenuto (Controller number 66)
Status 2nd byte
BnH 42H
n = MIDI channel number:
vv = Control value:
❍Soft (Controller number 67)
Status 2nd byte
BnH 43H
n = MIDI channel number:
vv = Control value:
❍Resonance (Controller number 71)
Status 2nd byte
BnH 47H
n = MIDI channel number:
vv= Resonance value (relative change):
* These messages are transmitted when Resonance value is set in EXTERNAL Zone.
❍Release Time (Controller number 72)
Status 2nd byte
BnH 48H
n = MIDI channel number:
vv = Release Time value (relative change): 00H - 7FH (-64 - 0 - +63)
* These messages are transmitted when Release Time is set in EXTERNAL Zone.
❍Attack Time (Controller number 73)
Status 2nd byte
BnH 49H
n = MIDI channel number:
vv = Attack time value (relative change): 00H - 7FH (-64 - 0 - +63)
* These messages are transmitted when Attack Time is set in EXTERNAL Zone.
❍Cutoff (Controller number 74)
Status 2nd byte
BnH 4AH
n = MIDI channel number:
vv = Cutoff value (relative change):
* These messages are transmitted when Cutoff value is set in EXTERNAL Zone.
❍Decay Time (Controller number 75)
Status 2nd byte
BnH 4BH
n = MIDI channel number:
vv = Decay Time value (relative change): 00H - 40H - 7FH (-64 - 0 - +63)
* These messages are transmitted when Decay Time value is set in EXTERNAL Zone.
162
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 40H - 7FH (Left - Center - Right)
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127) 0-63 = OFF, 64-127 = ON
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127) 0 - 63 = OFF, 64 - 127 = ON
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127) 0 - 63 = OFF, 64 - 127 = ON
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127) 0 - 63 = OFF, 64 - 127 = ON
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (-64 - 0 - +63)
3rd byte
vvH
0H - FH (ch.1 - 16)
3rd byte
vvH
0H - FH (ch.1 - 16)
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (-64 - 0 - +63)
3rd byte
vvH
0H - FH (ch.1 - 16)
❍Effect 1 (Reverb Send Level) (Controller number 91)
Status 2nd byte
BnH 5BH
n = MIDI channel number:
vv = Reverb Send Level:
* These messages are transmitted when Reverb value is set in EXTERNAL Zone.
❍Effect 3 (Chorus Send Level) (Controller number 93)
Status 2nd byte
BnH 5DH
n = MIDI channel number:
vv = Reverb Send Level:
* These messages are transmitted when Chorus value is set in EXTERNAL Zone.
❍RPN MSB/LSB (Controller number 100, 101)
Status 2nd byte
BnH 65H
BnH 64H
n = MIDI channel number: 0H - FH (ch.1 - 16)
mm = upper byte (MSB) of parameter number specified by RPN
ll = lower byte (LSB) of parameter number specified by RPN
<<< RPN >>>
Control Changes include RPN (Registered Parameter Numbers), which are extended.
When using RPNs, first RPN (Controller numbers 100 and 101; they can be sent in any
order) should be sent in order to select the parameter, then
Data Entry (Controller numbers 6 and 38) should be sent to set the value. Once RPN
messages are received, Data Entry messages that is received at the same MIDI channel after
that are recognized as changing toward the value of the RPN messages. In order not to
make any mistakes, transmitting RPN Null is recommended after setting parameters you
need.
This device transmits the following RPNs.
RPN Data entry
MSB, LSB MSB, LSB
00H, 00H mmH, llH
00H, 01H mmH, llH
00H, 02H mmH, llH
00H, 05H mmH, llH
7FH, 7FH ---, ---
●Program Change
Status 2nd byte
CnH ppH
n = MIDI channel number:
pp = Program number:
* When Rec Mode is ON (EDIT:Utility:Rec Setting:Rec Mode), these messages are
transmitted when Tone is selected.
●Pitch Bend Change
Status 2nd byte
EnH llH
n = MIDI channel number:
mm, ll = Pitch Bend value:
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127)
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127)
3rd byte
mmH
llH
Notes
Pitch Bend Sensitivity
mm: 00H - 18H (0 - 24 semitones)
ll: ignored (processed as 00H)
Channel Fine Tuning
mm, ll: 20 00H - 40 00H - 60 00H
(-4096 x 100 / 8192 - 0 - +4096 x 100 / 8192 cent)
Channel Coarse Tuning
mm: 10H - 40H - 70H (-48 - 0 - +48 semitones)
ll: ignored (processed as 00H)
Modulation Depth Range
mm, ll: 00 00H - 06 00H
(0 - 16384 x 600 / 16384 cent)
RPN null
RPN and NRPN will be set as "unspecified."
Once this setting has been made, subsequent
0H - FH (ch.1 - 16)
00H - 7FH (prog.1 - prog.128)
3rd byte
mmH
0H - FH (ch.1 - 16)
00 00H - 40 00H - 7F 7FH (-8192 - 0 - +8191)