Onkyo TX-NR474 Mode D'emploi page 56

> Before Start > Part Names
Double Bass This can be selected when the "Configuration" - "Subwoofer"
setting is "Yes" and the "Front" setting is "Full Band".
Boost bass output by sending the bass of the front speakers and
center speaker to the subwoofer.
"On": Bass output will be boosted.
"Off": Bass output will not be boosted.
0 The setting will not automatically be configured even if you
performed AccuEQ Room Calibration.
∫ 3. Distance
Set the distance from each speaker to the listening position.
Front Left Specify the distance between each speaker and the listening
position. (Default Value is "3.60 m")
Center Specify the distance between each speaker and the listening
position. (Default Value is "3.60 m")
Front Right Specify the distance between each speaker and the listening
position. (Default Value is "3.60 m")
Height Left Specify the distance between each speaker and the listening
position. (Default Value is "2.70 m")
Height Right Specify the distance between each speaker and the listening
position. (Default Value is "2.70 m")
Surround Right Specify the distance between each speaker and the listening
position. (Default Value is "2.10 m")
Surround Left Specify the distance between each speaker and the listening
position. (Default Value is "2.10 m")
Subwoofer Specify the distance between each speaker and the listening
position. (Default Value is "3.60 m")
0 Distance units can be switched by pressing MODE on the remote controller. When the
unit is set as feet, you can set between 0.1 ft and 30.0 ft in increments of 0.1 ft. When the
unit is set as meters, you can set between 0.03 m and 9.00 m in increments of 0.03 m.
56
> Install > Initial Setup > Playback
Advanced Setup
∫ 4. Level Calibration
Front Left Select a value between "-12 dB" and "+12 dB" (in 1 dB
increments). A test tone will be output each time you change the
value. Select the desired level. (Default Value is "0 dB")
Center Select a value between "-12 dB" and "+12 dB" (in 1 dB
increments). A test tone will be output each time you change the
value. Select the desired level. (Default Value is "0 dB")
Front Right Select a value between "-12 dB" and "+12 dB" (in 1 dB
increments). A test tone will be output each time you change the
value. Select the desired level. (Default Value is "0 dB")
Height Left Select a value between "-12 dB" and "+12 dB" (in 1 dB
increments). A test tone will be output each time you change the
value. Select the desired level. (Default Value is "0 dB")
Height Right Select a value between "-12 dB" and "+12 dB" (in 1 dB
increments). A test tone will be output each time you change the
value. Select the desired level. (Default Value is "0 dB")
Surround Right Select a value between "-12 dB" and "+12 dB" (in 1 dB
increments). A test tone will be output each time you change the
value. Select the desired level. (Default Value is "0 dB")
Surround Left Select a value between "-12 dB" and "+12 dB" (in 1 dB
increments). A test tone will be output each time you change the
value. Select the desired level. (Default Value is "0 dB")
Subwoofer Select a value between "-15 dB" and "+12 dB" (in 1 dB
increments). A test tone will be output each time you change the
value. Select the desired level. (Default Value is "0 dB")
∫ 5. Dolby Enabled Speaker
Dolby Enabled Set the distance between the Dolby enabled speaker and the
Speaker to Ceiling ceiling. Select a value between "0.1 ft/0.03 m" and "15.0 ft/
4.50 m" (in 0.1 ft/0.03 m increments, default value is "1.80 m")
0 The unit of distance (feet/meters) shown is the unit selected
for use in "Distance".
| Supplementary Information | Others