Functions On The Control Panel - Hedson W-550 Mode D'emploi

INSTRUCTIONS FOR USE
1. Turn on the red/yellow main switch.
2. Open the lid (nr 12 picture 3) and place the wheel into the machine, the outside of the wheel to the right as this side
washes most efficiently. Please note that possible decoration covers for example in plastic in the center of the rim
must be removed before washing the wheel.
We strongly recommend that also the valve cap is removed from the wheel before washing as this may cause operational
disturbances if it falls off during the wash cycle (see the chapter "TROUBLE SHOOTING").
Wheels with protruding parts on the rim sticking out more than 13 mm (1/2") beyond the contour of the tyre, are under no
circumstances to be washed in the Wheel Washer (symbol 4, picture 2). The protruding parts can be damaged.
For machines with SUV-kit 15170: Wheels with protruding parts on the rim, beyond the contour of the tyre, are under no
circumstances to be washed in the Wheel Washer. The protruding parts can be damaged.
If narrow wheels are incorrectly placed in the wash room, it can be difficult for them to rotate during the wash cycle. Place
the wheel in a way that it stands as straight as possible to minimize the risk that it will slide during the wash cycle.
A wheel with a puncture that has bees standing for so long, that it has turned flat at one point and is not round anymore,
can not be washed in the machine since it will not rotate properly.
3. Close the lid. Never let go of the lid, before it is either fully closed or fully open.
4. Start the machine (see item 5 in the next chapter).
After cleaning, the wheel will continue to rotate for 10 sec, and the granula on the wheel will be blown off by compressed
air. When the wheel has stopped rotating, the wash cycle is completed, and the wheel can be taken out. It is possible to run
an extra cycle with air blowing only (see item 8 in the next chapter).
(The basic setting of 10 secs. returnstroke with airblowing is re-programmed as follows: Simultaneously press on key 2
and key 90 secs. and set the desired time with key 30 or 60 secs. Afterwards confirm with key 120 secs.).
The machine is equipped with two security sensors. These will prevent the machine from operating if the lid is open or the
door to the motor room is not in place. Should you open the lid or door during operation, the washing will be interrupted
immediately. To resume washing, close the lid/door and press the start button again.
5. Finally, always check that there are no granula left on the tyre before it is mounted onto the car.

FUNCTIONS ON THE CONTROL PANEL

(See picture1)
1. LCD-display. Shows the number of wash cycles since the last water change.
2. When pressing this button, the diplay will show the total number of wash cycles of the machine.
3. A yellow light is flashing when the machine has washed 300 wheels (adjustable) and it is time to change the water in the
machine. When changing the water, press the button during 3 seconds to set the display to zero.
4. This button is used for collecting the granula (see the chapter "CHANGE OF WATER"). (The dynamic flush pipe will
then take a given position and the pump will run during 5 minutes.)
5. These are start buttons for the wash cycle. Preset duration of 30, 60, 90 or 120 sec. In all buttons a green light will be lit
when the machine is ready for operation. When you have started a wash cycle, the button you have pressed will remain lit
and the others will go out. (Before the pump motor starts, the dynamic flush pipe (nr 7 picture 3) will move to the starting
position if it is not alredy in that position.)
6. Stop and alarm button. A red light is lit when something is out of order. If you press the button during the wash, the
pump motor will stop and the dynamic flush pipe will move to the starting position. If the lid is opened during the wash
cycle, the operation will be interrupted immediately.
INSTR: 9594 REV: 100819/ Bom ÄM: 1758, 1812 GODK: SID: 4 / 32