Remote Control; General Control - Sharp XL-BB20D Mode D'emploi

Remote control

■ Battery installation
1
Open the battery cover.
2
Insert the batteries according to the terminal indicated in
the battery compartment. When inserting or removing the
batteries, push them towards the (–) battery terminals.
3
Close the cover.
Caution:
● Replace all old batteries with new ones at the same
time.
● Do not mix old and new batteries.
● Remove the batteries if the unit will not be used for a
long period of time. This will prevent potential damage
due to battery leakage.
● Do not use rechargeable batteries (nickel-cadmium
battery, etc.).
● Installing the batteries incorrectly may cause the unit
to malfunction.
● Batteries (battery pack or batteries installed) shall not
be exposed to excessive heat such as sunshine, fire
or the like.
Notes concerning use:
● Replace the batteries if the operating distance is re-
duced or if the operation becomes erratic. Purchase 2
"AAA" size batteries (UM/SUM4, R3, HP-16 or similar).
● Periodically clean the transmitter on the remote control
and the sensor on the unit with a soft cloth.
● Exposing the sensor on the unit to strong light may in-
terfere with operation. Change the lighting or the direc-
tion of the unit.
● Keep the remote control away from moisture, heat,
shock, and vibrations.
■ Test of the remote control
The remote control can be used within the range shown below:
Remote sensor
0.2 m - 6 m

General control

■ To turn the power on
Press the (ON/STANDBY) button to turn the power on or
off.
■ Display brightness control
Press the DIMMER button (remote control).
(Display is dim).
Dimmer 1
(Display gets dimmer).
Dimmer 2
(Display is bright).
Dimmer off
XL-BB20D_OM_EN_DE_ES_FR_IT_PL.indb 7
General control (continued)
■ Volume auto fade-in
If you turn off and on the main unit with the volume set to
27 or higher, the volume starts at 15 and fades in to the
last set level.
■ Volume control
Turn the volume knob towards VOL +/– (main unit) or
press VOL +/– (remote control) to increase or decrease
the volume.
■ Muting
To mute the volume, press the
Press again to restore the volume.
■ Direct key power on function
When you press any of the following buttons, the unit turns on.
CD / , USB / , BLUETOOTH
●
(INPUT), TUNER [DAB]: Selected function is activated.
/ (main unit): The unit turns on and playback of the last
●
function will start (CD, USB, BLUETOOTH, AUDIO IN,
LINE IN, TUNER, DAB)
(OPEN/CLOSE) (on main unit/remote control): Disc
●
tray opens and the last selected function is activated.
■ Auto power off function
The main unit will enter the standby mode after approxi-
mately 15 minutes of inactivity during:
Audio In/Line In: No detection of input signal.
CD: In the stop mode or no disc.
USB: In the stop mode or no media.
Bluetooth: - No connection after approximately 15 minutes.
- In the pause or stop mode and no incoming sig-
nal from device after approximately 15 minutes.
■ Bass or Treble control
1
Press the BASS or TREBLE button to select "Bass" or
"Treble" respectively.
2
Within 5 seconds, press the VOL (+ or –) button to adjust the
bass or treble.
- 5 ↔ - 4 ........ ↔ + 4 ↔ + 5
Press SOUND (DEFAULT) button to return sound to
default settings. "SOUND DEFAULT" appears on the
display.
Sound default settings : Bass = 0, Treble = 0
■ Function
Press the INPUT button (main unit) repeatedly to select
desired function.
CD FM STEREO
BLUETOOTH LINE IN
Note:
The backup function will protect the memorised function
mode for a few hours should there be a power failure or
the AC power lead becomes disconnected.
EN-7
button (remote control).
/ , AUDIO/LINE
- 5 ↔ - 4 ........ ↔ + 4 ↔ + 5
FM MONO DAB
AUDIO IN USB
2018-01-25 10:09:51