Télécharger Imprimer la page

GE UX12B36PSS Instructions D'installation

Le dosseret 30 cm 12
Masquer les pouces Voir aussi pour UX12B36PSS:

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

Installation
Instructions
WARNING
To prevent ignition of combustible
materials, the entire back wall above the range
must be protected by a backsplash constructed of
non-combustible material.
This stainless steel backsplash accessory must be
installed in combination with a custom, non-combustible
backsplash built beyond the 12" height of the backsplash.
BEFORE YOU BEGIN
Read these instructions completely and carefully.
IMPORTANT
for local inspector's use.
IMPORTANT
codes and ordinances.
■ Note to Installer — Be sure to leave these
instructions with the consumer.
■ Note to Consumer — Keep these instructions with
your Owner's Manual for future reference.
■ This kit provides for the installation of a 12" high
backsplash for 30", 36" or 48" Professional Ranges
and Rangetops.
TOOLS AND MATERIALS REQUIRED
■ G loves to protect against sharp edges
■ T -15 and #2 Phillips
screwdrivers
■ D rill with 3/32" and
9/64" bits
■ S afety glasses
■ L evel
■ P encil
This Kit Includes
■ W all support panel
■ C over panel
■ H ardware package with
– 5 Stainless Steel Torx 15
#8 self-tapping screws
– 5 Phillips #2 pan head wood
#10 screws
31-10690-1 01-18 GEA
— Save these instructions
— Observe all governing
Wall Support Panel
Cover Panel
Hardware
Package
761Dia65
UX12B36PSS
12" High Backsplash
INSTALL 12" BACKSPLASH
WARNING
This backsplash must be securely
fastened to the wall. Failure to do so could result in
damage or personal injury.
■ I nstall and level the range or rangetop and the
range hood according to the installation instructions.
■ R emove the backsplash packaging and protective
film.
■ U se a level to pencil a horizontal line on the wall, 1/8"
above the range or rangetop. The 1/8" gap allows the
cover panel to overlap the wall support panel.
■ L ocate wall studs on each side. Where studs are not
available, plan to use wall anchors (not provided).
■ A lign the wall support panel on the marked
horizontal line and centered left to right.
■ T he wall support panel must be secured to the wall
at all 4 corners. Use wood screws (provided) or wall
anchors (not provided) to secure the support panel
to the wall.
■ P lace the cover panel over the wall support panel
and secure with Torx screws (provided). Install 2
screws on each side.
Install 4 Wood Screws
1/8"
Wall
Cover Panel
Support
Panel
Wall Support
Panel
Center
Arrow
Install T-15
Screws

Publicité

loading

Sommaire des Matières pour GE UX12B36PSS

  • Page 1 Installation UX12B36PSS Instructions 12” High Backsplash INSTALL 12” BACKSPLASH WARNING To prevent ignition of combustible WARNING materials, the entire back wall above the range This backsplash must be securely must be protected by a backsplash constructed of fastened to the wall. Failure to do so could result in non-combustible material.
  • Page 2 Instructions UX12B36PSS d’installation Le Dosseret 30 cm (12”) INSTALLEZ LE DOSSERET 30 CM (12”) AVERTISSEMENT Afin d’éviter que les matériaux AVERTISSEMENT inflammables ne prennent feu, le mur arrière au-dessus de la Ce dosseret doit être cuisinière doit être protégé par un dosseret en matériau ignifuge.
  • Page 3 Instrucciones UX12B36PSS de instalación Salpicadero Alto 12” INSTALE EL SALPICADERO DE 12” ADVERTENCIA Para prevenir el encendido de ADVERTENCIA materiales combustibles, debe protegerse toda la pared Este salpicadero debe estar bien trasera de la cocina mediante un salpicadero construido con sujeto a la pared. No hacerlo puede provocar daños o...
  • Page 4 NOTE: While performing installations described in this book, safety glasses or goggles should be worn. NOTE: Product improvement is a continuing endeavor. Therefore, materials, appearance and specifications are subject to change without notice. REMARQUE : lorsque vous procédez aux installations abordées dans ce manuel, il est fortement recommandé de porter des lunettes de sécurité. REMARQUE : la philosophie fait la part belle à l’innovation. C’est pourquoi les matériaux, les caractéristiques et l’apparence extérieure peuvent faire l’objet de modifications sans préavis.