Control Unit; General Safety Precautions - Aprimatic Slide 230 Instructions D'installation, D'utilisation Et D'entretien

CONTENTS
ABOUT THIS MANUAL
Information
THIS INSTRUCTION MANUAL DESCRIBES THE INSTALLATION OF THE
ELECTRICAL COMPONENTS ON THE SLIDE
FOR INSTRUCTIONS ABOUT INSTALLING MECHANICAL COMPONENTS
SEE THE SUPPLIED INSTRUCTIONS
!
Warning
THIS INSTRUCTION MANUAL IS AN INTEGRAL PART OF THE PRO
.
DUCT IT SHOULD BE STORED IN A ACCESSIBLE PLACE READY FOR
.
IMMEDIATE REFERENCE THIS MANUAL SHOULD ACCOMPANY THE
PRODUCT THROUGHOUT ITS LIFE CYCLE UP UNTIL DECOMMISSIONING
FAILURE TO OBSERVE THE SAFETY PRECAUTIONS GIVEN IN THIS MANUAL
,
FOR THE ASSEMBLY FITTING AND TESTING OF THIS AUTOMATION UNIT
AND GATE CAN LEAD TO PERSONAL INJURY AND DAMAGE TO EQUIPMENT
READ THE INSTRUCTION MANUAL CAREFULLY BEFORE ANY OPERATIONS
THESE INSTRUCTIONS MUST KEPT CLOSE TO THE INSTALLATION
FOR IMMEDIATE REFERENCE DURING USE AND MAINTENANCE
Caution
THE INFORMATION IN THIS MANUAL IS PROVIDED AS A GUIDE ONLY
THE MANUFACTURER DECLINES ALL LIABILITY FOR ERRORS AND OMIS
.
SIONS IN THIS MANUAL
THE COMPANY RESERVES THE RIGHT TO MODIFY THE PRODUCT AND
MAKE ANY IMPROVEMENTS WITHOUT PRIOR NOTICE

GENERAL SAFETY PRECAUTIONS

CAREFULLY READ THE INSTRUCTIONS BEFORE STARTING TO INSTALL
.
THE PRODUCT
!
Warning
(
PACKING MATERIALS PLASTIC
DISPERSED IN THE ENVIRONMENT AND MUST NOT BE LEFT WHERE CHIL
DREN CAN FIND THEM AS THEY ARE A POTENTIAL SOURCE OF DANGER
DO NOT USE THE PRODUCT FOR NON
DO NOT TAMPER WITH OR MODIFY THE PRODUCT IN ANY WAY
INCORRECT INSTALLATION OF THE PRODUCT MAY CAUSE SERIOUS
.
HAZARDS FOLLOW ALL THE INSTALLATION INSTRUCTIONS CAREFULLY
ONLY PROFESSIONALLY QUALIFIED PERSONNEL SHOULD INSTALL THE
.
PRODUCT
WE RECOMMEND OPERATING IN A WELL
,
MENT IN COMPLIANCE WITH THE SAFETY REGULATIONS IN FORCE
RECOMMEND THE USE OF APPROVED PROTECTIVE CLOTHING
,
SHOES PROTECTIVE GOGGLES
ARTICLES OF CLOTHING THAT COULD GET CAUGHT
TAKE ADEQUATE SAFETY MEASURES TO PREVENT THE RISK OF INJURY
CAUSED BY SHARP SPLINTERS AND THE POSSIBLE RISKS OF CRUSHING
KNOCKS AND CUTS OR AMPUTATION
DELIMIT THE YARD TO PREVENT ANY UNAUTHORISED PERSONS FROM
TRANSITING IN THE WORKING AREA
.
UNATTENDED
SLIDE 230
1. P
RODUCT DESCRIPTION
1.1 PERMITTED USE AND FIELD OF APPLICATION ..... 16
1.2 TECHNICAL FEATURES ............................................ 16
1.3 TECHNICAL SPECIFICATIONS ................................. 16
2. I
NSTALLATION
2.1 ASSEMBLING/REPLACING THE UNIT ..................... 16
2.2 ELECTRIC SYSTEM SET-UP .................................... 17
2.3 ELECTRICAL CONNECTIONS .................................. 17
3. S -
YSTEM START
3.1 PRELIMINARY CHECKS: INPUTS - WEIGHT CLASS
- PINION TYPE - M/S CONFIGURATION - OPENING
DIRECTION ................................................................ 19
3.2 SELF-TEACHING ....................................................... 19
3.3 SAVING THE REMOTE CONTROLS ......................... 20
4. F
UNCTIONING
4.1 OPERATING LOGICS ................................................ 21
4.2 INPUTS AND OUTPUTS ............................................ 23
4.3 CHECKS AND WARNINGS ON DISPLAY................. 23
5. P
ROGRAMMING THE
6. N
OTES FOR MAINTENANCE TECHNICIANS
6.1 ROUTINE MAINTENANCE ........................................ 25
7. I
NFORMATION FOR THE USER
230
CONTROL UNIT ONLY
.
.
.
, , .)
POLYSTYRENE ETC MUST NOT BE
-
SPECIFIED OR IMPROPER PURPOSES
.
-
LIT AND HEALTHY ENVIRON
, ).
GLOVES AND HELMET DO NOT WEAR
.
.
.
DO NOT LEAVE THE WORKING AREA
UP
P
ARAMETERS
WE RECOMMEND STRICT OBSERVATION OF THE NATIONAL REGULATIONS
FOR SAFETY IN WORK SITES
COMBINED WITH LEGISLATIVE DECREE
92/57/EC
DIRECTIVE
LATIONS ON HEALTH AND SAFETY AT WORK TO BE OBSERVED WHEN
WORKING ON TEMPORARY OR MOBILE SITES
,
. INSTALLATION ELECTRICAL CONNECTIONS AND ADJUSTMENTS MUST BE
, CARRIED OUT IN A PROFESSIONAL MANNER IN COMPLIANCE WITH THE
GOOD MANUFACTURING AND WORKMANSHIP REGULATIONS IN FORCE IN
THE COUNTRY WHERE THE AUTOMATION IS INSTALLED
THE MANUFACTURER OF THE DEVICE IS NOT RESPONSIBLE FOR THE
-
NON OBSERVANCE OF PROFESSIONAL STANDARDS OF WORK IN THE
CONSTRUCTION OF THE POWER
-
DAMAGE WHICH MAY BE CAUSED BY THE USE OF THE DRIVE
INCORRECT INSTALLATION MAY BE DANGEROUS
FOLLOW THE MANUFACTURER
.
BEFORE STARTING INSTALLATION
AND THAT THE EXISTING STRUCTURE IS SUITABLY STRONG AND STA
.
BILE
.
.
,
Information
READY
ONLY SUITABLY SKILLED TECHNICIANS TRAINED ON THE PRODUCT
ARE AUTHORISED TO CONNECT UP
.
PRODUCT
WE STRONGLY RECOMMEND FOLLOWING A SPECIALISED TRAINING
.
.
COURSE INSTALLERS SHOULD CONTACT THE SUPPLIER FOR INFOR
-
MATION ON COURSES
AT THE END OF THE WORK THE INSTALLER MUST CHECK THE INSTALLATION
IS DONE CORRECTLY AND THE AUTOMATION WORKS PROPERLY
BEFORE YOU TEST OR PUT INTO SERVICE THIS PRODUCT YOU MUST
CHECK THAT IT CONFORMS TO THE RELEVANT SECTIONS OF THE MACHI
2006/42/EC
NERY DIRECTIVE
THE TECHNICAL DOSSIER FOR THE PRODUCT AND BE ABLE TO PRODUCE
THE DOSSIER WHENEVER REQUESTED
THE INSTALLER SHOULD ASSESS THE RISKS CONNECTED WITH THE
PRODUCT AND CHECK THAT THERE ARE NO CRUSHING OR SHEARING
HAZARDS PRESENT
MUST BE TAKEN AND ALL OF THE SIGNS REQUIRED BY THE REGULATIONS
IN FORCE TO WARN OF ANY DANGEROUS ZONES MUST BE ATTACHED
-
EVERY INSTALLATION MUST CLEARLY INDICATE THE ID DATA FOR THE
-
.
POWER DRIVEN SYSTEM
.
THE INSTALLER MUST PROVIDE FULL INFORMATION ABOUT THE AUTOMA
,
TIC MANUAL AND EMERGENCY FUNCTIONING OF THE EQUIPMENT AND
DELIVER THE OPERATING INSTRUCTIONS TO THE SYSTEM USER
ONLY USE ORIGINAL SPARE PARTS FOR ANY REPAIRS OR FOR REPLACING
.
.
PARTS THE GUARANTEE IS VOID IF THIS PRODUCT IS USED IN COMBINA
TION WITH OTHERS OF OTHER BRANDS
-
THE MANUFACTURER OF THE DRIVE DECLINES ANY RESPONSIBILITY IF
.
COMPONENTS INCOMPATIBLE WITH SAFETY AND CORRECT OPERATION
WE
.
(
ARE INSTALLED
SAFETY
!
Warning
,
IN THE EVENT OF ANY FAULTS DISCONNECT THE OPERATOR FROM
THE MAINS POWER SUPPLY USING THE MAIN SWITCH
REPAIR THE MAIN UNIT
ASSISTANCE CENTRE
RESULT IN HAZARDOUS SITUATIONS
- 15 -

CONTROL UNIT

16
16
19
21
23
25
25
( ,
IN ITALY LEGISLATIVE DECREE
"
494/96
IMPLEMENTATION OF
CONCERNING THE MINIMUM RULES AND REGU
").
-
DRIVEN STRUCTURE
.
' .
S INSTRUCTIONS
,
CHECK THAT THE PRODUCT IS INTACT
,
TEST AND PUT INTO SERVICE THIS
.
.
THE INSTALLER MUST BE IN POSSESSION OF
.
.
IF NECESSARY SPECIAL PREVENTIVE MEASURES
.
.
.
CONTACT THE INSTALLER OR OTHER SPECIALIST
.
FAILURE TO FOLLOW THESE INSTRUCTIONS MAY
.
528/99
-
.
,
NOR FOR ANY
.
-
-
.
-
.
-
.
-
.
DO NOT TRY TO