Displaying The Firmware Version; Displaying The Open Source Licenses; Updating Firmware; Audio Adjustments - Pioneer AVH-X7800BT Manuel Du Propriétaire

System settings

Color:
Adjusts the color saturation. (–24 to +24)
 Hue:
Adjusts the tone of color (which color is emphasized, red or
green). (–24 to +24)

Dimmer:
Adjusts the brightness of the display. (+1 to +48)

Temperature:
Adjusts the color temperature, resulting in a better white
balance. (–3 to +3)
p With some pictures, you cannot adjust Hue and Color.
 When you touch [Rear View], the mode changes
to the selected camera mode. By touching
[Source], [Navi] or [Apps], you can return to the
selected mode.
5 Touch , , , to adjust.
p The adjustments of "Brightness", "Contrast" and "Dimmer"
are stored separately when your vehicle's headlights are off
(daytime) and on (nighttime).
p "Brightness" and "Contrast" are switched automatically
depending on whether the vehicle's headlights are on or off.
p "Dimmer" can be changed the setting or the time to switch
it to on or off.
 Refer to Setting the dimmer on page 37
p The picture adjustment may not be available with some rear
view cameras.
p The setting contents can be memorized separately.
Displaying the firmware
version
1 Display the "System" setting screen.
 Refer to Displaying the "System" setting screen on page
35
2 Touch [System Information].
3 Touch [Firmware Information].
The "Firmware Information" screen appears.
Displaying the open source
licenses
1 Display the "System" setting screen.
 Refer to Displaying the "System" setting screen on page
35
2 Touch [System Information].
38
3 Touch [License].
The open source licenses of the functions that this product is
equipped with appear.

Updating firmware

CAUTION
 The USB storage device for updating must contain only the
correct update file.

Never turn this product off, disconnect the USB storage
device while the firmware is being updated.
 You can only update the firmware when the vehicle is
stopped and the parking brake is engaged.
1 Download the firmware update files.
2 Connect a blank (formatted) USB storage
device to your computer, and then locate the
correct update file and copy it onto the USB
storage device.
3 Connect the USB storage device to this
product.
4 Turn the source off.
 Refer to Selecting a source on page 12
5 Display the "System" setting screen.
 Refer to Displaying the "System" setting screen on page
35
6 Touch [System Information].
7 Touch [Firmware Update].
8 Touch [Continue] to display the data transfer
mode.
p Follow the on-screen instructions to finish updating the
firmware.
p This product will reset automatically after the firmware
update is completed if the update is successful.
p If an error message appears on the screen, touch the display
and perform the above steps again.
Audio
adjustments
Displaying the "Audio" setting
screen
1 Press .
2 Touch , and then .
The "Audio" setting screen appears.

Using fader/balance adjustment

1 Display the "Audio" setting screen.
 Refer to Displaying the "Audio" setting screen on page 38
2 Touch [Fader/Balance].
p Only the balance can be adjusted when "Network Mode" is
selected as the speaker mode. Touch [Balance] and skip to
step 4.
3 Touch or to adjust the front/rear speaker
balance.
p Set "Front" and "Rear" to "0" when using a dual speaker
system.
4 Touch or to adjust the left/right speaker
balance.
 You can also set the value by dragging the point
on the displayed table.
Switching sound muting/
attenuation
You can automatically mute or attenuate the AV source volume
and the iPhone application volume when the navigation outputs
the guidance voice.
1 Display the "Audio" setting screen.
 Refer to Displaying the "Audio" setting screen on page 38
2 Touch [Mute Level].
3 Touch the item.
 ATT (default):
The volume becomes 20 dB lower than the current volume.

Mute:
The volume becomes 0.

Off:
The volume does not change.