BFT CLONIX Instructions D'utilisation Et D'installation page 11

in the "collective receivers" mode, as well as manage the complete
installation database using the EEdbase software.
5) MANUAL PROGRAMMING
In the case of standard installations where no advanced functions are
required, it is possible to proceed to manual storage of the transmitters,
making reference to programming table A and to the example for basic
programming in Fig.2.
1) If you wish the transmitter to activate output 1, press pushbutton
SW1, otherwise if you wish the transmitter to activate output 2,
press pushbutton SW2.
2) If you wish to obtain functions other than monostable activation,
refer to table A – output activation.
3) When LED DL1 starts blinking, press hidden key P1 on the
transmitter, LED DL1 will remain continuously lit.
Note: Hidden key P1 appears differently depending on the
transmitter model.
For TRC 1-2 / MITTO 2-4, press hidden key P1 (Fig.3).
For TRC 4, the key P1 function corresponds to simultaneously
pressing the 4 transmitter keys or, after opening the battery
compartment, bridging the two P1 points by means of a screwdriver
(Fig.3).
4) Press the key to be memorised on the transmitter, LED DL1 will
start blinking again.
5) To memorise another transmitter, repeat steps 3) and 4).
6) To exit the storage mode, wait until the LED is switched off
completely.
IMPORTANT NOTE: ATTACH THE ADHESIVE KEY LABEL TO THE
FIRST MEMORISED TRANSMITTER (MASTER).
In the case of manual programming, the first transmitter assigns the
key code to the receiver; this code is necessary in order to carry out
subsequent cloning of the radio transmitters.
6) RADIO TRANSMITTER CLONING
6.1) Cloning with rolling-code (JP5 connected)
Clones can be added by means of UNIRADIO, and the only limitation
to this is the maximum number of transmitters the receiver can
memorise.
Note: in rolling-code cloning, the level of safety of the code anti-
copying system is very high, and is the same as that of the transmitters
memorised manually in the receivers.
Knowledge of the cloning key code or the reading from the key
transmitter allow the operator to create additional clones by remote
control, without needing further information.
To create replacement clones, you need to have the complete receiver
memory data; therefore, if you plan to carry out replacement cloning
operations by remote control, you need to memorise the contents of
the receiver memory by reading it using UNIRADIO and entering it in
the EEdbase database.
When assigning a specific key on an additional clone transmitter to a
specific output channel on a receiver, a predefined procedure is
followed which can be decided at will if the radio transmitter storage is
carried out by means of UNIRADIO, or otherwise is identical to the key
transmitter procedure.
The keys on the replacement clone transmitter maintain the same
association with the output channels of the receiver as the replaced
transmitter.
Code reading:
In the case where a receiver code in not known, reading can be
obtained by proceeding in the following way.
1) Switch UNIRADIO on and wait for the welcome message.
2) Use the <arrow up> and <arrow down> keys to select item <go
the menu number>.
3) Press <enter>.
4) When in the subsequent menu, type number 225 and press
<enter>.
5) Follow the instructions appearing on the UNIRADIO display.
Cloning by addition:
a) Cloning by addition with code
Having carried out key code reading, you are advised to write it down
INSTALLATION MANUAL
on the appropriate card supplied and given to the user (Fig.6).
For practical clone creation, refer to instructions on the UNIRADIO
device or, for clone addition, observe the following simplified procedu-
re:
1) Switch UNIRADIO on and wait for the welcome message.
2) Use the <arrow up> and <arrow down> keys to select item <go
the menu number>.
3) Press <enter>.
5) When in the subsequent menu, type number 2121 and press
<enter>.
6) Follow the instructions appearing on the UNIRADIO display.
b) Cloning by addition with master
For practical clone creation by means of the master transmitter
(marked with the key label) refer to the instructions on the UNIRADIO
device, or observe the following simplified procedure:
1) Switch UNIRADIO on and wait for the welcome message.
2) Use the <arrow up> and <arrow down> keys to select item <go
the menu number>.
3) Press <enter>.
5) When in the subsequent menu, type number 2122 and press
<enter>.
6) Follow the instructions appearing on the UNIRADIO display.
Cloning by replacement:
During the replacement cloning procedure, you are requested to
specify the position taken up in the receiver memory by the transmitter
to be eliminated. It is therefore indispensable to have the complete
data of the said position; this operation can only be carried out through
unloading the data by means of UNIRADIO and entering them in the
EEdbase database.
1) Switch UNIRADIO on and wait for the welcome message.
2) Use the <arrow up> and <arrow down> keys to select item <go
the menu number>.
3) Press <enter>.
5) When in the subsequent menu, type number 2314 and press
<enter>.
6) Follow the instructions appearing on the UNIRADIO display.
6.2) Cloning with fixed code (JP5 open)
In the cases where you do not wish to manage the list or the cloning
key or the key transmitter, additional clones can be generated by
means of UNIRADIO, starting from any transmitter which is already
memorised within the system. This operation can only be carried out
if the receiver is configured to operate with a fixed code (no longer a
rolling code) by removing bridge JP5 in Fig. 4.
NOTE: ALTHOUGH A HIGH NUMBER OF COMBINATIONS FOR
TRANSMITTER CODING IS INCLUDED IN THE FIXED CODE
CONFIGURATION, THE SAFETY LEVEL OF THE CODE ANTI-
COPYING SYSTEM IS INFERIOR.
When assigning a specific key on an additional clone transmitter to a
specific output channel on a receiver, a predefined procedure is
followed which can be decided at will if the radio transmitter storage is
carried out by means of UNIRADIO, or otherwise is identical to the key
transmitter procedure.
For fixed code clone creation, refer to the UNIRADIO instructions or
observe the following simplified procedure:
1) Switch UNIRADIO on and wait for the welcome message.
2) Use the <arrow up> and <arrow down> keys to select item <go
the menu number>.
3) Press <enter>.
4) When in the subsequent menu, type number 21 and press <enter>.
5) Select menu <fixed code cloning> and press <enter>.
6) Follow the instructions appearing on the UNIRADIO display.
7) COLLECTIVE RECEIVERS
Collective installations can be carried out by means of the UNIRADIO
programmer. For instance, just one transmitter can be used to control
a "collective" receiver (ref. "C", Fig.5), and an "individual" receiver (ref.
PX, Fig. 5).
In this type of installation, the appropriate codes need to be assigned
to the various receivers by means of UNIRADIO.
ENGLISH
CLONIX/TRC/MITTO - Ver. 02 - 11