Sanremo ZOE COMPACT SAP Livret D'instructions page 19

ENGLISH
Connect the power cable (G) to the socket.
N.B. CHECK THAT THE DATA ON THE RATING PLATE CORRESPOND TO YOUR MAINS ELECTRICITY SUPPLY.
When installed, the boiler and heat exchangers are dry to avoid possible damage to the appliance caused by freezing.
1) The appliance must be supplied with cold water only.
2) If the mains pressure is higher than 0.6 Mpa (6 bars), you must install a pressure regulator with 0.6 Mpa (6 bars) maximum output pressure.
3) Connect the drain hose to the drip tray, avoiding excessively tight curves and sloping the hose appropriately to facilitate water flow.
4) Connect the 3/8" hose to the mains water supply, then to the water softener and the appliance.
Connect to the mains water supply in respect of national legislation.
N.B. The water softener is indispensable for correct operation of the appliance, to optimise coffee delivery in the cup and to extend the working life
of components, as it purifies the water from limescale and residues that would otherwise shorten working life.
Failure to follow these instructions absolves the company from all liability.
Before connecting the pump intake tube, open the tap and run water through the water softener for about two minutes to eliminate possible.
The impurities filter (code 10355150) is normally
mounted on the hose connecting the purifier to the
pump (fig. A) to prevent impurities in the water from
damaging downstream components such as the
pumping head, flow pumps, solenoid valves, etc.
The capsule filter (code 10355162) which blocks
the impurities present in the water must be replaced
about every three months.
The three month period is indicative only as the
actual length of time is correlated to water con-
sumption and the impurities present in the mains
water supply.
To replace the pod filter: unscrew the impurities filter
(code 10355150) and replace the pod filter.
Before inserting the new pod filter, make sure the
inside of the body (10355152 and 10355154) is
completely clean. Any foreign matter must be re-
moved to ensure correct filtration.
The impurities filter must be mounted according to
the flow direction indicated by the arrow (fig. A) on
the body.
Before using the appliance, check that:
- the plug is inserted properly into the mains power outlet;
- the water filling hose is correctly connected to the mains water outlet, check for leaks and that the water tap is open;
- the drain pipe is positioned in accordance with the preceding instructions.
With the steam tap (B) open, place the ON/OFF switch (D) in the 1 position and wait for the water in the boiler to
reach the maximum level established by the electronic control unit. If the boiler does not fill within the set time-
out (90 secs.), the pump stops and the keypad LEDs flash. In this case put the on/off switch (D) to position 0
and then to position 1 to finish filling the boiler.
Now put the on/off switch (D) to position 2 so that the heating elements are powered and therefore start to
heat the water.
Wait for steam to come out the steam nozzle (B), then close the tap and, using the Boiler pressure gauge,
check that the pressure has reached and maintains a value of 0.8:1 bar. Pressure switch
If this is not the case, use a screwdriver to regulate the adjustment screw in the pres-sure switch (+ to
increase, - to decrease, see figure below).
Make sure the boiler pressure gauge shows a pressure of 0.5:1 bars.
Press the button (M6) to deliver hot water, then press again to stop delivery.
Take great care to avoid burns.
All models have two steam nozzles on the sides of the work surface, with the exception of the one group machine which has just one. These steam
ELECTRICAL CONNECTION
WATER CONNECTION
IMPURITIES FILTER
USE
PRELIMINARY CHECK
HOT WATER DELIVERY
STEAM DELIVERY
19
Part.1 = 10355150
10355156
10355162
10355152
A
1
Fig. A
10355154