Ryobi TVM01 Manuel D'utilisation page 9

LED LIGHT FUNCTIONS
See Figure 2, page 14.
When the tool is charged, the LED light will indicate the
status of the battery.
BATTERY STATUS
Normal
Battery Level < 25%
Low Battery
Excessive Force
Over Temperature
OVERLOAD PROTECTION
When the tool is forced or the motor is overloaded, the tool
will automatically shut off. To reset the tool, wait 5 seconds,
slide the on/off switch to the OFF position and then slide it to
the ON position to resume operation. Do not force the tool.
HIGH TEMPERATURE PROTECTION
This tool is equipped with a high temperature protection
feature that automatically deactivates the tool when it is
overheated. To resume operation, allow the tool to cool and
then turn the tool on.
CHARGING THE TOOL
See Figure 2, page 14.
 Turn off the rotary tool.
 Insert the USB-C cable into the product as shown.
 Connect the USB cable to any powered USB port, or
connect it to a USB power adapter (not included) and
plug the adapter into a power supply.
 Make sure the power supply is normal household voltage,
120 volts, AC only, 60 Hz.
 When the tool is charging, the LED will flash green.
 Do not place tool in an area of extreme heat or cold. It
will charge best at normal room temperature.
 If the LED flashes red at any point during charging, an
error has occurred. Remove the USB cable and attempt
to charge the tool later.
 After charging is complete, the LED will stop flashing and
will remain green.
 Disconnect the USB power adaptor (not included) from
the power supply or disconnect the USB cable from the
powered USB port once the tool is fully charged and ready
for use.
 Disconnect the USB-C cable from the tool.
OPERATION
LED LIGHT SCENARIO
Solid Green (No Flashes)
Solid Red (No Flashes)
Flashing Red (3 Flashes)
Flashing Red (6 Flashes)
Flashing Red (9 Flashes)
9 - English
QUICK-CHANGE COLLET
See Figures 3 - 4, pages 14 .
NOTE: The tool ships with a preinstalled collet that is
machined to precision tolerances to fit accessories with
1/8 in. diameter shanks. When installed, the quick change
collet allows the user to change accessories without tools
and without removing the collet from the shaft. The quick
change collet is not compatible with 1/16 in. shanks.
To remove/install the quick change collet:
 Turn off the rotary tool.
 Depress and hold the spindle lock button and rotate the
shaft by hand until the spindle lock engages the shaft,
preventing further rotation.
 With the spindle lock engaged, place the included 3/8 in.
wrench on the bottom threaded end of the quick-change
collet and turn counterclockwise to loosen. Continue
turning counterclockwise to remove the collet from the
tool.
 Remove the quick-change collet.
 To install, engage the spindle lock. Place the quick-
change collet on the shaft and begin threading on by
hand until there is resistance. Then use the included 3/8
in. wrench on the bottom threaded end of the collet and
rotate clockwise until tightly secured.
WARNING:
Always use the collet which matches the shank size of the
accessory you plan to use. Never force a large diameter
shank into a collet. The accessory should fit smoothly
into the collet, but you should be able to tighten the ac-
cessory firmly and securely with the quick-change collet.
INSTALLING/REMOVING ACCESSORIES
See Figures 3 - 4, pages 14 .
To install:
 Turn off the rotary tool.
 Choose an accessory that fits the collet and is suitable
for the application you are attempting.
 Ensure the quick-change collet is securely installed on
the shaft.
 While depressing the spindle lock, use your hand to
loosen the collet by rotating the sleeve counterclockwise.
 Insert the shank of the accessory into the collet until the
shank bottoms out, then pull it out 1/16 in. to allow for
expansion when the accessory gets hot.
 Rotate the collet sleeve clockwise until clicking stops and
the accessory shank is gripped by the collet.
NOTE: If sleeve cannot be tightened or loosened
sufficiently by hand, use the included 3/8 in. collet wrench
on the top hexed area of the collet. Turn clockwise to
tighten or counterclockwise to loosen.