EINHELL TC-SM 2131/2 Dual Instructions D'origine page 26

6. Operation
Warning! To make 90° crosscuts, the adjustable
stop rail (34) must be fi xed at the inner position:
•
Undo the locking screw (9) of the adjustable
stop rail and push the adjustable stop rail
inwards.
•
The adjustable stop rail (34) must be fixed far
enough in front of the innermost position that
the distance between the stop rail (34) and
the saw blade (7) amounts to a maximum of
8 mm.
•
Before making a cut, check that the stop rail
and the saw blade cannot collide.
•
Tighten the locking screw (9) again.
Warning! To make 0°-45° miter cuts to the left
(with the machine head (4) inclined or with the
turntable set at an angle), the adjustable stop rail
(34) must be fi xed at an outer position.
•
Undo the locking screw (9) of the adjustable
stop rail and push the adjustable stop rail
outwards.
•
The adjustable stop rail (34) must be fixed far
enough in front of the innermost position that
the distance between the stop rail (34) and
the saw blade (7) amounts to a maximum of
8 mm.
•
Before making a cut, check that the stop rail
and the saw blade cannot collide.
•
Tighten the locking screw (9) again.
Warning! This saw is equipped with a removable
stop rail (36) which is screwed to the right-hand
side of the fi xed stop rail (11).
To make 0°-45° miter cuts to the right (with the
machine head (4) inclined or with the turntable
set at an angle), the removable stop rail (36) must
be completely removed. Warning! In this case the
maximum permissible workpiece height is redu-
ced (see 4. Technical data).
•
Open the locking screw (9) of the removable
stop rail (36) far enough for you to be able to
remove the stop rail (36) in upwards direction.
•
Always fasten the removable stop rail (36) on
the equipment again after you have comple-
ted your work.
•
The stop rail must always be kept together
with the equipment. A removed stop rail will
impair the operational safety of the equip-
ment.
Anl_TC_SM_2131_2_Dual_SPK9.indb 26
GB
6.1 Cross cut 90° and turntable 0°
(Fig. 1-3, 11)
For cutting widths up to approx. 100 mm it is
possible to fi x the saw's drag function with the
locking screw for drag guide (24) in rear position.
If the cutting width exceeds 100 mm you must
ensure that the locking screw for drag guide (24)
is slackened and that the machine head (4) can
be moved.
•
Move the machine head (4) to its upper po-
sition.
•
Use the handle (1) to push back the machine
head (4) and fix it in this position if required
(dependent on the cutting width).
•
Place the piece of wood to be cut at the stop
rail (11) and on the turntable (17).
•
Lock the material with the clamping device
(8) on the fixed saw table (18) to prevent the
material from moving during the cutting ope-
ration.
•
Push down the release lever (3) to release the
machine head (4).
•
Press the On/Off switch (2) to start the motor.
•
With the drag guide fixed in place: Use the
handle (1) to move the machine head (4)
steadily and with light pressure downwards
until the saw blade (7) has completely cut
through the workpiece.
•
With the drag guide not fixed in place: Pull the
machine head (4) all the way to the front and
then use the handle (1) to move it downwards
steadily and with light pressure. Now push the
machine head (4) slowly and steadily to the
very back until the saw blade (7) has comple-
tely cut through the workpiece.
•
When the cutting operation is completed,
move the machine head (4) back to its upper
(home) position and release the On/Off but-
ton (2).
Important! The integral resetting springs will
automatically lift the machine head. Do not simply
let go of the handle (1) after cutting, but allow the
machine head (4) to rise slowly, applying slight
counter pressure as it does so.
6.2 Cross cut 90° and turntable 0° - 45°
(Fig. 1-3, 12)
The crosscut saw can be used to make crosscuts
of 0°- 45° to the left and 0° - 45° to the right in re-
lation to the stop rail.
•
Release the turntable (17) by undoing the
locking screw (14).
•
Turn the turntable (17) and scale pointer (15)
to the desired angular setting on the dial (16)
and lock into place with the locking screw
- 26 -
30.09.2021 15:22:52