Remote Control - Dimplex CAS500 Mode D'emploi

• is used to mute the fire crackling sound. Press this to turn on and off the crackling sound. The volume can be
adjusted on the manual controls of the appliance. Please note that the mute setting will not be saved after a product
restart. The crackling sound can be turned off completely by using the volume control buttons on the button panel to
reduce the volume to its minimum setting. This minimum setting will be remembered after a product restart.
• is the reduce flame button. Press the upper reduce flame button to reduce the height/intensity of the flame on the
left hand side of the product. Press the lower reduce flame button to reduce the height/intensity of the flame on the
right hand side of the product. You will hear an audible beep when you reach the minimum level.
• is the increase flame button. Press the upper increase flame button to increase the height/intensity of the flame
on the left hand side of the product. Press the lower increase flame button to increase the height/intensity of the
flame on the right hand side of the product. You will hear an audible beep when you reach the maximum level.

REMOTE CONTROL

The remote control is supplied with 2xAAA batteries. Remove the battery cover from the underside of the remote control
and after removing the batteries from the plastic wrapping fit them into place. Replace the battery cover. With the product
powered off, a functional test can be carried out on the remote control by pushing any button and observing the blue LED
at the top o the remote flashing with each button push.
Pairing the Remote Control
The remote control has wireless Bluetooth technology and needs to be paired to the receiver. This can be done by
following the steps below.
1. Press the rocker switch to the on (I) position; a single beep will be heard.
2. Press the button on the Button Panel; the product will turn on.
3. Press the button on the Button Panel, the LED's will start to slowly blink on and off.
4. Press the button on the remote control; the product LEDs will flash quickly three times and the product will then
automatically switch off. The remote control is now paired to the product and can be used to switch it back on.
The operation of the remote control is the same as described in 'Receiver Controls'. You can pair multiple products to the
one remote control by repeating the pairing operation as above on your subsequent products. Please note a maximum
of six CAS500 or CAS1000 products can be paired to the one remote control.
Pairing the Remote Control to Multiple Products
If you are installing multiple CAS500/CAS1000 products you can pair them to a single remote control. To do this, please
install the products as described in the "Installation Instructions". Ensure that all products are connected to mains power
and have water supplied. If you are pairing CAS1000 and CAS500 products please choose the 6 button remote control
as the master remote control.
1. Pair the first product as described in steps 1-4 above.
2. On your second product, press the rocker switch to the on (I) position; a single beep will be heard.
3. Press the button on the Button Panel; the product will turn on.
4. Press the button on the Button Panel, the LED's will start to slowly blink on and off.
5. Press the button on the remote control; the LEDs will flash quickly three times and the product will then
automatically switch off. The remote control is now paired to the two products and can be used to switch them on.
6. Repeat the above steps to pair the next product.
7. When all products are paired, test the remote control by pressing the
a signal from the remote control you can bring that product back in line with the others via the Manual Controls or
the receiver controls.
GETTING THE DESIRED FLAME EFFECT
1. Switch the appliance on by pressing the main switch to the on position and pressing the
start after 45seconds.
2. Press the and
to the changes you make.
Once you have made your adjustments to both the flame height and crackling sound, the appliance will keep these
settings even if you power off the appliance by either the on/standby button or by the main switch. The next time you
switch on the appliance, it will start up as normal, wait 45 seconds for the flames to start and then revert to the adjusted
settings.
Nozzle Inserts
Nozzle inserts have been supplied and fitted to the nozzle opening. These inserts are used to alter the profile of the
flame effect. These inserts can be removed if a different flame profile is preferred. In addition to these inserts, inserts for
blocking the flame in certain areas have also been supplied. To fit these inserts, remove the exisitng inserts that have
been supplied and fitted to the product. Break the blocking inserts into the required length. Snap the inserts into the
nozzle opening in the desired location. See Fig 22 for further deatils.
buttons to adjust the flame to your desired level. Please give the flame generator time to react
button. If any of the products fail to receive
6
button. The flames will