Installazione; Installation - CAIROX 900x900 Manuel D'installation

Cassette à eau
Table des Matières

Publicité

Rif. 22-01
Rif. 22-02
A
C
Rif. 22-03
Rif. 22-04
A
Rif. 22-05
22
>1400
5
B
D
A
A
DETTAGLIO A
DETTAGLIO A
SCALA 1 : 5
SCALA 1 : 5
ITA

INSTALLAZIONE

FISSAGGIO DELLA CASSETTA
Scegliere un luogo per l'installazione
in maniera tale che attorno alla mac-
china vi siano spazi di almeno 140 cm.
Verificare che l'installazione non inter-
ferisca con l'impianto elettrico o idrau-
lico già esistente.
Determinare la posizione e la dimen-
sione del foro sul soffitto utilizzando la
dima di cartone. Scegliere la posizio-
ne finale dell'unità nel soffitto con
l'ausilio dei riferimenti stampati sulla
dima di cartone.
Per il fissaggio dell'unità al soffitto, uti-
lizzare della barra filettata con dei tas-
selli adeguati come illustrato in figura
(materiale non incluso nella fornitura).
Inserire tra la la staffa di ancoraggio e
la barra filettata di sostegno un ade-
guato antivibrante in gomma.
Assicurarsi, con l'aiuto di una livella a
bolla, che l'unità sia posizionata oriz-
zontalmente ed adeguatamente bloc-
cata al soffitto. Nei locali con un alto
tasso di umidità, i sostegni metallici
devono essere isolati mediante un
materiale isolante adesivo.
FISSAGGIO DEL PANNELLO
Una volta fissata saldamente l'unità,
montare la griglia di plastica fissando
le viti in dotazione.
NOTA BENE: è molto importante fis-
sare la griglia nella giusta posizio-
ne in maniera da effettuare corret-
tamente
la
connessione
del
pannellino ricevitore con l'unità.
- Per il fissaggio del pannello utiliz-
zare solo ed esclusivamente le 4
viti in dotazione.
L'utilizzo di viti più lunghe può dan-
neggiare la bacinella raccogli con-
densa.
- Non piegare o strozzare le tubazioni
dell'unità.
- Rimuovere la chiusura dei tubi
dell'unità solo immediatamente prima
di effettuare i collegamenti.
- Al fine di evitare la deformazione del-
la griglia, si raccomanda di non strin-
gere eccessivamente le viti.
ENG

INSTALLATION

FIXING THE CASSETTE
Select a place of installation where
there can be a clearance of a least
140 cm around the appliance. Make
sure that the installation does not
interfere with existing electric wiring
or plumbing.
Establish the position and size of the
hole in the ceiling using the cardboard
mounting template.
To fix the unit to the ceiling, use the
threaded bar and suitable screw an-
chors as shown in picture (material
not included in the supply).
Insert a suitable antivibration rubber
between the bracket and threaded
bar.
Use a spirit level, to make sure that
the unit is level and check that it is se-
curely fixed to the ceiling. In high hu-
midity environments, metal supports
must be insulated using adhesive in-
sulating material.
FIXING THE PANEL
After installation of the unit, mount
the grille using the 4 screws provided.
ATTENTION: It is very important to fix
the grille in the right position for cor-
rect connection of the receiver panel
to the unit.
- To fix the panel only use the 4 sup-
plied screws.
Do not use other kinds of screws or
you could damage the condensate
drain pan.
- Do not bend or narrow the unit pi-
ping.
- Do not remove the cap from the unit
piping until immediately before con-
necting the pipes.
- To prevent deformation of the air in-
take grille, do not overtighten the
screws.

Publicité

Table des Matières
loading

Table des Matières