Technical Data; Noise/Vibration Information - Bosch GWS Professional 18 V-LI Notice Originale

(1) Direction of rotation arrow on housing
(2) Spindle lock button
(3) On/off switch
(4) Hex key
a)
(5) Rechargeable battery
(6) Rechargeable battery release button
(7) Vibration-damping auxiliary handle (insulated grip-
a)
ping surface)
(8) Standard auxiliary handle (insulated gripping sur-
face)
(9) Locking screw for protective guard
(10) Protective guard for grinding
(11) Protective guard for cutting
(12) Cover for cutting
(13) Mounting flange with O‑ring
a)
(14) Grinding disc
(15) Disc brush (dia. 22.22 mm)
a)
(16) Disc brush (M 14)
a)
(17) Cutting disc

Technical Data

Angle grinder
Article number
Rated voltage
A)
Rated speed
Max. grinding disc diameter/rubber sanding pad diameter
Grinding spindle thread
Max. thread length of grinding spindle
Weight according to EPTA-Procedure 01:2014
Recommended ambient temperature during charging
Permitted ambient temperature during operation
storage
Recommended rechargeable batteries
Recommended chargers
A) Rated no-load speed for the selection of appropriate application tools in accordance with EN IEC 62841-2-3. The actual speed is lower for
safety reasons and according to production tolerances.
B) Depends on rechargeable battery (5), protective guard ((11), (10), (12)) and auxiliary handle ((8), (7)) in use
C) Limited performance at temperatures < 0 °C

Noise/Vibration Information

Noise emission values determined according to
EN IEC 62841-2-3.
Typically the A-weighted noise level of the power tool are: 85
dB(A); sound power level 93 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN IEC 62841-2-3:
Bosch Power Tools
(18) Diamond cutting disc
(19) Quick-clamping nut with bar
(20) Clamping nut
(21) Quick-clamping nut
(22) Two-pin spanner for clamping nut/round nut
a)
(23) Handle (insulated gripping surface)
(24) Grinding spindle
(25) Hand guard
(26) Rubber sanding pad
(27) Abrasive disc
(28) Round nut
(29) Cup brush
a)
(30) Conical brush
(31) Diamond annular cutter
(32) Open-ended spanner
(33) Extraction guard for cutting with cutting guides
a)
a) Accessories shown or described are not included with the
B)
C)
and during
Surface grinding (roughing) and abrasive cutting:
a
Disc sanding:
a
Grinding thin metal sheets or other materials that tend to easily vi-
brate with a large surface area can cause the noise emission value to
increase by up to 15 dB. Suitable, heavy damping mats can reduce
the increased noise emissions. Increased noise emissions must be
taken into consideration, both for the risk assessment of the noise
output and for selecting suitable hearing protection.
a)
a)
a)
a)
a)
a)
a)
a)
a)
product as standard. You can find the complete selection of
accessories in our accessories range.
GWS 18V-LI
3 601 J3A 300
V= 18
-1
min 11,000
mm 115
M 14
mm 22
kg 2.0–3.2
°C 0 to +35
°C –20 to +50
GBA 18V...
ProCORE18V...
GAL 18...
GAX 18...
GAL 36...
2 2
= 6.0 m/s , K = 1.5 m/s ,
h
2 2
= 2.5 m/s , K = 1.5 m/s .
h
English | 23
a)
a)
a)
GWS 18-125 V-LI
3 601 J3A 301
18
11,000
125
M 14
22
2.0–3.2
0 to +35
–20 to +50
GBA 18V...
ProCORE18V...
GAL 18...
GAX 18...
GAL 36...
1 609 92A 767 | (07.03.2022)