Napoleon MIRAGE 730 Mode D'emploi page 11

11
Infrared Burners: Because of the high intensity of the infrared burner, most drippings and food particles that
fall onto the burner surface are immediately incinerated. However, some debris and residue may remain. To
remove this residue after cooking, turn the grill on high with lid closed for 5-10 minutes. Do not clean the ce-
ramic tile with a wire brush. If debris is collecting on your burner, simply light the burner and operate on high
for 5 minutes with the lid open, allowing debris to burn off. If the back burner is not used often, grease splat-
ter from main burner grilling will eventually block the ports. Once a month, the back burner should be fired
for 5-10 minutes to burn off the accumulated grease.
Protection Of Infrared Burners: The infrared burners of your grill are designed to provide a long service life,
though care must taken to prevent cracking of their ceramic surfaces. Fractures will cause the burners to
malfunction. The following provides a few of the causes of cracks and the steps you can take to avoid them.
Damage caused by failure to follow these steps is not covered by your grill warranty.
1. Impact with hard objects - Never allow hard objects to strike the ceramic. Take care when inserting or re-
moving cooking grates and accessories into or from the grill.
2. Contact with water or other liquids - Cold liquids contacting the hot ceramic surfaces can cause them to
break. Never throw water into the grill to douse a flame. If the ceramic or interior of a burner becomes wet
while not in use, later operation of the burner can create steam, which can produce sufficient pressure to crack
the ceramic. Repeated soaking of the ceramic can also cause it to swell and expand. This expansion causes
undue pressure on the ceramic that can cause it to crack and crumble.
ceramic for evidence of possible watersoaking. If the ceramic appears to be wet, remove the burner from the
grill. Turn it upside down to drain the excess water and bring indoors to dry thoroughly.
3. Impaired ventilation of hot air from the grill - For the burners to function properly, hot air must have a way
to escape the grill. If the hot air is not allowed to escape, the burners can become deprived of oxygen causing
them to back-flash. If this occurs repeatedly, the ceramic could crack. Never cover more than 75% of the cook-
ing surface with solid metal (i.e., griddle or large pan).
4. Incorrect cleaning - Do not clean the ceramic tile with a wire brush. If debris is collecting on your burner,
light the burner and operate on high for 5 minutes with the lid open, allowing debris to burn off.
Problem
Low heat / Low flame
when valve turned to
high.
Excessive flare-ups/
uneven heat.
www.napoleongrills.com
i) Never throw water into the grill to control flare-ups.
ii) Do not attempt to operate the infrared burners in open air while raining.
iii) If you find standing water in your grill (because of exposure to rainfall, sprinklers, etc.), inspect the
Troubleshooting
Possible Causes
For propane - improper lighting procedure.
For natural gas - undersized supply line.
For both gases - improper preheating.
Sear plates installed incorrectly.
Improper preheating.
Excessive grease and ash build on sear plates
and in drip pan.
Solution
Ensure lighting procedure is followed
carefully. All gas grill valves must be in the
off position when the tank valve is turned
on. Turn tank on slowly to allow pressure
to equalize. See lighting instructions.
Pipe must be sized according to
installation code.
Preheat grill with both main burners on
high for 10 to 15 minutes.
Ensure sear plates are installed with the
holes towards the front and the slots on
the bottom. See assembly instructions.
Preheat grill with both main burners on
high for 10 to 15 minutes.
Clean sear plates and drip pan regularly.
Do not line pan with aluminum foil. Refer
to cleaning instructions.