Technical Data; Before Starting The Equipment - EINHELL TC-MX 1400-2 E Instructions D'origine

Masquer les pouces Voir aussi pour TC-MX 1400-2 E:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 21

4. Technical data

Mains voltage: .........................220-240 V~ 50 Hz
Power input: ............................................ 1400 W
Idling speed: ...........................0-480 / 0-780 min
Mixing tool mount: ........................................ M14
Protection class: ............................................ II/
Weight: .....................................................3.19 kg
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 62841.
L
sound pressure level ..................... 88.6 dB(A)
pA
K
uncertainty ............................................. 3 dB
pA
L
sound power level ....................... 99.6 dB(A)
WA
K
uncertainty ............................................. 3 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 62841.
Right handle
Vibration emission value a
K uncertainty = 1.5 m/s
Left handle
Vibration emission value a
K uncertainty = 1.5 m/s
The stated vibration emission levels and stated
noise emission values were measured in ac-
cordance with a set of standardized criteria and
can be used to compare one power tool with
another.
The stated vibration emission levels and stated
noise emission values can also be used to make
an initial assessment of exposure.
Warning:
The vibration and noise emission levels may vary
from the level specifi ed during actual use, depen-
ding on the way in which the power tool is used,
especially the type of workpiece it is used for.
Anl_TC_MX_1400_2_E_SPK9.indb 15
Anl_TC_MX_1400_2_E_SPK9.indb 15
-1
= 0.718 m/s
2
h
2
= 1.146 m/s
2
h
2
- 15 -
GB
Keep the noise emissions and vibrations to a
minimum.
Only use appliances which are in perfect wor-
king order.
Service and clean the appliance regularly.
Adapt your working style to suit the appliance.
Do not overload the appliance.
Have the appliance serviced whenever ne-
cessary.
Switch the appliance off when it is not in use.
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
Mixer assembly (Fig. 2-3):
First scew mixer part (6a) together with mixer part
(6b). Screw the mixer (6) into the mixer holder (4)
afterwards. Use the two spanners to do this. Use
one of the spanners (7a) to hold the mixer holder
(4) in place and then use the second spanner (7b)
to tighten up the mixer (6). Proceed in the reverse
sequence to undo the mixer.
is secure (pull the mains plug).
09.03.2021 06:55:46
09.03.2021 06:55:46

Publicité

Chapitres

Table des Matières
loading

Ce manuel est également adapté pour:

42.585.50

Table des Matières