Accessories; Replacement Parts - LIFT-MASTER PRO8000 Instructions

MAINTENANCE OF YOUR OPENER
Once a Month:
• Repeat safety reverse test. Make any necessary adjustments.
• Manually operate door. If it is unbalanced or binding, call for
professional garage door service.
• Check to be sure door opens and closes fully. Adjust Limits
and/or Force if necessary.
Once a Year:
Oil door rollers, bearings and hinges. The opener does not require
additional lubrication. Do not grease the door tracks.
SPECIAL FEATURES OF THE PRO8000 23
A. Door within a door connection
Remove cover. Locate auxiliary terminal block. Remove jumper
from terminal leads 1 and 2 (not shown). Replace with contact
switch leads as shown.
B. Flashing light connection
The flashing light can be installed anywhere. Connect light leads to
terminals 3 and 4 on the terminal block.
C. Coaxial antenna adapter
A coaxial antenna connection can be used if the transmitter range
is too short. Cut off the existing antenna. Use standard coax cable
and connector. Strip off end of insulation to "X" dimension.
418/433 MHz: X = 250mm
Reposition antenna.
24

ACCESSORIES

8000-27 8000-418 8000-433
(1) Models 750E 4180E
(2) Model 751E
(3) Models 752E 4182E
(4) Models 4183E
(5) Model 754E
(6) Models 4185E
(7) Models 727E 787E
(8) Model 58LM..................................Multi-Function Door
(9) Model 75LM ..................................Lighted Door Control Button
(10) Model 760E ..................................Outside Keylock
(11) Model 1702E ................................Outside Quick Release
(12) Model 770E ..................................The Protector System™
(13) Model 1703E ................................The Chamberlain Arm™
(14) Model FLA230 ..............................Flashing Light Kit
(15) Model 16200LM ...........................Pedestrian Door Switch
(16) Model MDL100LM ........................Mechanical Door Latch Kit
(17) Model EQL01 ...............................Door Handle Quick Release
(18) Model 100027 ..............................1-Position Key Switch
Model 100041 ..............................2-Position Key Switch
114A2054D-GB
27 MHz: X = 2,44m
4330E Single-Function Remote Control
Single-Function Remote Control
(with code switches)
4332E 2-Function Remote Control
(with 1 code switch)
4333E 3-Function Remote Control
4-Function Remote Control
(with 1 code switch)
4335E 3-Function Mini Remote Control
747E Wireless Keyless Entry Keypad
Control Panel
(Flush Mount - 100010)
(Flush Mount - 100034)
24
ACCESSORIES (Continued)
WIRING INSTRUCTIONS FOR ACCESSORIES
Lighted Push Button: To opener terminals: Red-1 and White-2.
Outside Keylock: To opener terminals: Red-1 and White-2.
Protector System™: To opener terminals: White-2 and Black-3.
Door Control Panel:To opener terminals: Red-1 and White-2.

REPLACEMENT PARTS

SPECIFICATIONS
Rated Pull Force 800N
..................
Motor
Type Permanent split capacitor
...........................................
Speed 1500 rpm
........................................
Volts 230-240 Volts 50Hz only
...........................................
Current 2,0 amperes
.....................................
Drive Mechanism
Length of Travel Adjustable to 3.5m (11.5 feet)
...................
(with 3m rail)
Travel Rate 18cm (7.1 inches) per second
.............................
Lamp 2 x 40 W, on when door starts, off 4-1/2
.........................................
minutes after stop. Bulbs not included.
Door Linkage Adjustable door arm. Pull cord trolley
.........................
release.
Safety
Personal Push button and automatic reversal in down
...................................
direction. Push button and automatic stop in
up direction.
Electronic Independent up and down force adjustment
................................
screws.
Electrical Low voltage push button wiring.
..................................
Limit Adjustment Screwdriver adjustment on side panel.
..................
Start Circuit Low voltage push button circuit.
............................
Dimensions
Length (Overall) 3,20m (10.6 feet) (with standard rail)
...................
Headroom Required 40mm (1.5 inches)
..........
Hanging Weight 14,5 kg (32 lb)
...................
Receiver
Memory Registers 12
...............
Code Switch Memory 1
........
Keypad Code Memory 1
......
D e c l a r a t i o n o f C o n f o r m i t y
Automatic Garage Door Opener................................................................Model PRO8000
is in conformity to the
applicable sections of Standards .....................................................EN55014, EN61000-3,
per the provisions & all amendments
of the EU Directives .....................................................................73/23/EEC, 89/336/EEC
D e c l a r a t i o n o f I n c o r p o r a t i o n
Automatic Garage Door Opener Model PRO8000, when installed and maintained
according to all the Manufacturer's instructions in combination with a Garage Door,
which has also been installed and maintained according to all the Manufacturer's
instructions, meet the provisions of EU Directive 89/392/EEC and all amendments.
I, the undersigned, hereby declare that the equipment
specified above and any accessory listed in the manual
conforms to the above Directives and Standards.
Chamberlain GmbH
D-66793 Saarwellingen
March, 1999
25 - 26
ETS 300 683,
EN60555, & EN60335-1
Colin B. Willmott
Chefingenieur