Dmx Linking; Signal Connection; Art-Net ™ Connection; Wireless Operation - Chauvet Professional MAVERICK SILENS 2 PROFILE Manuel De Référence

Contact
Outside the U.S., U.K., Ireland, Benelux, France, Germany, or Mexico, contact your distributor to request support or
return a product. Refer to
What is Included
• Maverick Silens 2 Profile
• Seetronic Powerkon IP65 power cord
• Gel frame holder and gel frame
CAUTION: Do not supply power to fixture until you have removed internal packing foam. Remove head
cover, carefully remove internal packing foam and replace cover.
AC Power
This product has an auto-ranging power supply that can work with an input voltage range of 100–240 VAC, 50/60 Hz.
Power linking
It is possible to link up to 2 Maverick Silens 2 Profile products at 100/120 V, 4 products at 208 V, or 4 products at
230/240 V. Never exceed this number. Power-linking cords can be purchased separately from Chauvet.
AC plug
Connection
AC Live
AC Neutral
AC Ground
To eliminate unnecessary wear and improve its lifespan, during periods of non-use completely
disconnect the product from power via breaker or by unplugging it.
Replacing the fuse
1. Disconnect the product from power.
2. Using a flathead screwdriver, unscrew the fuse holder cap from the housing.
3. Remove blown fuse and replace with a good fuse of the same type and rating.
4. Screw the fuse holder cap back in place and reconnect power.

DMX Linking

The Maverick Silens 2 Profile will work with a DMX controller using a 3- or 5-pin DMX serial connection. A DMX Primer is
available from www.chauvetprofessional.com.
DMX connection
The Maverick Silens 2 Profile uses a 3- or 5-pin DMX data connection for its DMX personalities: 32Ch and 41Ch. See the
User Manual for information about connecting and configuring the product for DMX operation.
RDM (Remote Device Management)
Remote Device Management, or RDM, is a standard for allowing DMX-enabled devices to communicate bi-directionally
along existing DMX cabling. Check the DMX controller's User Manual or with the manufacturer, as not all DMX controllers
have this capability. The Maverick Silens 2 Profile supports RDM protocol that allows feedback to make changes to menu
map options. Download the User Manual from

Signal Connection

The Maverick Silens 2 Profile can link to controller software using an Ethernet connection. If using other Art-Net™ or
sACN -compatible products with the Maverick Silens 2 Profile, you can control each individually on a single network. See
the User Manual for information about how to connect and configure the product for these signals.
Art-Net connection
™
Art-Net™ is an Ethernet protocol that uses TCP/IP, which transfers a large amount of DMX512 data using a Neutrik
®
etherCON RJ45 connection over a large network. An Art-Net™ protocol document is available from
www.chauvetprofessional.com. Chauvet Professional recommends using unicast Art-Net™ for best results.
Art-Net™ designed by and copyright Artistic Licence Holdings Ltd.
sACN connection
Streaming-ACN, also known as ANSI E1.31, is an Ethernet protocol that uses the layering and formatting of Architecture
for Control Networks to transport DMX512 data over IP or any other ACN-compatible network.

Wireless Operation

In optimal conditions, the Maverick Silens 2 Profile can operate up to 300 m (900 ft) away from the CRMX transmitter.
The CRMX receiver in the Maverick Silens 2 Profile must be paired with the CRMX transmitter for wireless operation.
Download the User Manual from
Maverick Silens 2 Profile QRG Rev. 7
QUICK REFERENCE GUIDE
Contact Us at the end of this QRG for contact information.
Wire (U.S.)
Black
White
Green/Yellow
www.chauvetprofessional.com
www.chauvetprofessional.com
• 2 spare gobo holders
• 2 Omega brackets with mounting hardware
• Quick Reference Guide
Wire (Europe)
Brown
Blue
Green/Yellow
for more details.
for more details.
EN
Screw Color
Yellow/Brass
Silver
Green
®
2