Main Screen - nVent RAYCHEM HWAT-ECO-GF Mode D'emploi

Test
program start

MAIN SCREEN

HOT WATER MAINTENANCE
NOW
131°F
Contains 3 areas:
SYSTEM
1. Actual Maintain temperature (red area) INFO, RESET, SERVICE, TEST....
2. Next event temperature (grey area)
HOT WATER MAINTENANCE
HEATING CABLE & PIPE
3. Hot water storage temperature
CABLE TYPE, PIPE DAIMETER,...
(white area- if boiler sensor is connected and active)
GENERAL SETTINGS
NOW
Additional icons for settings, relay (ON/OFF), key lock or warning will be displayed. COUNTRY, LANGUAGES, UNITS,...
131°F
When Lock is "on" a password is needed to access the parameter menus.
WATER TEMP. & PROGRAM
After the correct 4 number password is entered, each parameter in the setup can be
APPARTMENT, MAINTAIN, ECONOMY,....
changed. The unit locks again after a 10 min. time out (no keys pressed).
131°F
SETTINGS
INFO
TEST PROGRAM
SYSTEM
INFO, RESET, SERVICE, TEST....
RESET
HEATING CABLE & PIPE
CABLE TYPE, PIPE DAIMETER,...
SERVICE
GENERAL SETTINGS
COUNTRY, LANGUAGES, UNITS,...
STATUS
WATER TEMP. & PROGRAM
APPARTMENT, MAINTAIN, ECONOMY,....
SYSTEM
INFO
SELECT CABLE TYPE
TEST PROGRAM
SELECT PIPE DIAMETER
INFO
RESET
SELECT INSULATION THICKNESS
TEST PROGRAM
SERVICE
RESET
SELECT AMBIENT TEMPERATURE
STATUS
SERVICE
SELECT BOILER SENSOR
STATUS
SELECT BOILER CUT-OFF TEMPS.
Info
SELECT CABLE TYPE
SELECT PIPE DIAMETER
SELECT CABLE TYPE
SELECT INSULATION THICKNESS
SELECT PIPE DIAMETER
SELECT AMBIENT TEMPERATURE
SELECT INSULATION THICKNESS
The economy temperature is the water
temperature for periods in which the amount of
hot water used is low (at night) or high (peak
period).Select the temperature using the +/-
keys. The minimum temperature is 98°F (37°C)
for use in environments such as schools, and
106°F (41°C) in the Apartments program. The
maximum temperature is the selected maintain
temperature.
The test program runs for 30 minutes, during
which all parameters will be ignored to check
heating cable and connection on site. You can
stop the test program at any time.
SETTING
HOT WATER MAINTENANCE
NOW
SYSTEM
SETTING
SETTING
SYSTEM
INFO, RESET, SERVICE, TEST....
HEATING CABLE & PIPE
CABLE TYPE, PIPE DAIMETER,...
GENERAL SETTINGS
COUNTRY, LANGUAGES, UNITS,...
WATER TEMP. & PROGRAM
APPARTMENT, MAINTAIN, ECONOMY,.... SYSTEM
HEATING CABLE & PIPE
SYSTEM
HEATING CABLE & PIPE
General info about the unit, name, commissioning date,
HWAT-R2
firmware version, nVent contact info per country.
HEATING CABLE & PIPE
DN 25
40 MM
20 °C
02:14 p.m.
NEXT
131°F
ECONOMY TEMP
AT 05:00 p.m.
BOILER
140 °F
14 : 17
02:14 p.m.
NEXT
131°F
ECONOMY TEMP
NEXT
AT 05:00 p.m.
131°F
BOILER
ECONOMY TEMP
140 °F
14 : 17
AT 05:00 p.m.
BOILER
140 °F
14 : 17
14 : 17
14 : 17
HWAT-R2
DN 25
40 MM
20 °C
ON
35/85 °C
14 : 17
HWAT-R2
DN 25
40 MM
SELECT LANGUAGE
grey area
SELECT COUNTRY
SELECT DATE
white area
SELECT TIME
SELECT ALARM
red area
SELECT SAVING TIME
SELECT LANGUAGE
SELECT WATER TEMPERATURE
02:14 p.m.
SELECT COUNTRY
SELECT PROGRAM
SELECT DATE
PROGRAM TIMER
SELECT TIME
SELECT ALARM
SELECT SAVING TIME
14 : 17
SELECT WATER TEMPERATURE
SELECT PROGRAM
PROGRAM TIMER
14 : 17
14 : 17
nVent.com | 13
GENERA
SELECT LANGUAGE
SELECT COUNTRY
SELECT DATE
SELECT TIME
SELECT ALARM
SELECT SAVING TIME
WATER T
SELECT WATER TEMPERATUR
SELECT PROGRAM
PROGRAM TIMER