Fein WSG8-115 Serie Mode D'emploi page 27

Handling hazardous dusts
For work procedures with this power tool where
material is removed, dusts develop that can be hazard-
ous to one's health.
Contact with or inhaling some dust types, e. g. asbestos
and asbestos-containing materials, lead-containing coat-
ings, metal, some wood types, minerals, silicate parti-
cles from materials containing stone, paint solvents,
wood preservatives, antifouling paints for vessels, can
trigger allergic reactions to the operator or bystanders
and/or lead to respiratory infections, cancer, birth
defects or other reproductive harm. The risk from
inhaling dusts depends on the exposition. Use dust
extraction matched appropriately for the developing
dust, as well as personal protective equipment and pro-
vide for good ventilation of the workplace. Leave the
processing of asbestos-containing materials to special-
ists.
Wood and light-metal dust, hot mixtures of grinding
dust and chemical materials can self-ignite under unfa-
vourable conditions or cause an explosion. Avoid
sparking in the direction of the dust collector as well as
overheating of the power tool and the materials being
sanded, empty the dust collector/container in time,
observe the material manufacturer's working instruc-
tions, as well as the relevant regulations in your country
for the materials being worked.
Operating Instructions.
The self-start lock prevents the angle grinder (see
Table) from automatically restarting again, even after a
brief interruption of the power supply, e. g., from a
pulled mains plug.
Angle grinder with self-start lock (see Table).
WSG8-115 (**)
WSG8-125 (**)
WSG11-125 (**)
Angle grinder with self-start lock and electronics (see
Table) are equipped with overload and blocking protec-
tion. In case of overload or blocking of the application
tool, the power supply is interrupted. In this case,
switch the power tool off, remove it from the work-
piece and check the application tool. Afterwards, switch
the power tool on again.
WSG12-125P (**)
WSG12-125PQ (**)
WSG15-125P (**)
WSG15-125PQ (**)
WSG15-70 Inox (**)
WSG17-125P (**)
WSG17-125PQ (**)
WSG17-125PS (**)
WSG17-125PSQ (**)
WSG17-150P (**)
Press the locking button only when the motor is
stopped (see page 8).
In the EU
WSG17-150PQ (**)
WSG17-70 Inox (**)
WSG15-125PR (**)
WSG15-125PRT (**)
WSG17-125PR (**)
WSG17-125PRT (**)
WSG17-150PR (**)
WSG17-150PRT (**)
WSG17-70 InoxR (**)
WSG17-70 InoxRT (**)
Repair and customer service.
When working metal under extreme oper-
ating conditions, it is possible for conductive
dust to settle in the interior of the power
tool. The total insulation of the power tool can be
impaired. Blow out the interior of the power tool via
the ventilation slots frequently with dry and oil-free
compressed air, and connect a residual current device
(RCD) on the line side.
If the supply cord of this power tool is damaged, it must
be replaced by a specially prepared cord available
through the FEIN customer service centre.
The current spares parts list for this power tool can be
found on our website at www.fein.com.
If required, you can change the following parts your-
self:
application tools, auxiliary handle, clamping flanges,
wheel guard
Warranty and liability.
The warranty for the product is valid in accordance
with the legal regulations in the country where it is mar-
keted. In addition, FEIN also provides a guarantee in
accordance with the FEIN manufacturer's warranty dec-
laration.
The delivery scope of your power tool may include
only a part of the accessories described or shown in this
Instruction Manual.
Declaration of conformity.
FEIN declares itself solely responsible for this product
conforming with the relevant provisions given on the
last page of this Instruction Manual.
Technical documents at: C. & E. Fein GmbH,
D-73529 Schwäbisch Gmünd
Environmental protection, disposal.
Packaging, worn out power tools and accessories
should be sorted for environmental-friendly recycling.
Selection of accessories (see page 16).
Use only original FEIN accessories. The accessories
must be intended for the power tool type.
A Grinding disc, flap disc
(use only with mounted wheel guard)
B Cutting disc
(use only with mounted cut-off wheel guard)
C Steel wire brush, fleece backing pad
D Backing pad for fibre sanding sheets, fibre sanding
sheets
(mount only with the provided backing-pad clamp-
ing unit; use only with mounted hand guard or wheel
guard)
E Steel tapered twist brush
F Backing pad with Velcro, Velcro sanding sheets,
sanding fleece with Velcro attachment, sponges
(use only with mounted hand guard)
G Steel cup brush, round twist brushes
(use only with mounted hand guard)
en
27