Sander Safety Warnings - Makita 9046 Manuel D'instructions

ENGLISH
(Original instructions)
1 Lock button
2 Switch trigger
3 Front grip
4 Conventional type of abrasive
paper
5 Clamp lever
6 Pad
SPECIFICATIONS
Model
Pad size ............................................. 115 mm x 229 mm
Abrasive paper size ........................... 115 mm x 280 mm
–1
Orbits per minute (min
Overall length ..................................................... 283 mm
Net weight ............................................................. 3.1 kg
Safety class ...............................................................
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2014
Intended use
The tool is intended for the sanding of large surface of
wood, plastics and metal materials as well as painted
surfaces.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
General power tool safety warnings
WARNING: Read all safety warnings, instructions,
illustrations and specifications provided with this
power tool. Failure to follow all instructions listed below
may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future refer-
ence.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.

SANDER SAFETY WARNINGS

1. Always use safety glasses or goggles. Ordinary
eye or sun glasses are NOT safety glasses.
2. Hold the tool firmly.
3. Do not leave the tool running. Operate the tool
only when hand-held.
4. This tool has not been waterproofed, so do not
use water on the workpiece surface.
5. Ventilate your work area adequately when you
perform sanding operations.
4
Explanation of general view
7 Velcro type of abrasive paper
8
9
10 Dust bag
11 Entry port
12 Dust spout
13 Groove
) ....................................... 6,000
Mark
Mark
6. Some material contains chemicals which may be
toxic. Take caution to prevent dust inhalation
9046
and skin contact. Follow material supplier safety
data.
7. Use of this tool to sand some products, paints
and wood could expose user to dust containing
hazardous substances. Use appropriate respira-
tory protection.
/II
8. Be sure that there are no cracks or breakage on
the pad before use. Cracks or breakage may
cause a personal injury.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity with product
ENE052-1
(gained from repeated use) replace strict adherence
to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this instruc-
tion manual may cause serious personal injury.
ENF002-2 FUNCTIONAL DESCRIPTION
CAUTION:
• Always be sure that the tool is switched off and
unplugged before adjusting or checking function on the
tool.
Switch action (Fig. 1)
GEA010-2
CAUTION:
• Before plugging in the tool, always check to see that
the switch trigger actuates properly and returns to the
"OFF" position when released.
To start the tool, simply pull the switch trigger. Release
the switch trigger to stop.
For continuous operation, pull the switch trigger and then
push in the lock button.
To stop the tool from the locked position, pull the switch
trigger fully, then release it.
Front grip (Fig. 2)
The front grip position can be changed in 90° increments.
GEB021-4
Pull the front grip and rotate it to the desired position.
ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
14 Front fixing cardboard
15 Front side of paper dust bag
16 Claws
17 Upper part
18 Notch
19 Guide