Optional Accessories - Makita 9046 Manuel D'instructions

Installing or removing abrasive paper
For conventional type of abrasive paper with pre-
punched holes (standard equipment):
Turn the clamp lever counterclockwise. Insert the paper
end into the clamper, aligning the holes in the paper with
those in the pad. Then return the clamp lever to the origi-
nal position to secure the paper. Repeat the same pro-
cess for the other end of the tool, maintaining the proper
paper tension. (Fig. 3 & 4)
For the velcro type of abrasive paper (accessory)
(Fig. 5)
Remove all dirt or foreign matter from the pad. Attach the
paper to the pad, aligning the holes in the paper with
those in the pad.
CAUTION:
• Always use velcro type of abrasive papers. Never use
pressure-sensitive abrasive papers.
ust bag (Fig. 6)
D
To install the dust bag, align the
entry port with the mark on the dust spout of the tool
and fit the entry port onto the dust spout. Then turn the
dust bag clockwise to secure it in place.
For the best results, empty the dust bag when it becomes
approximately half full, tapping it lightly to remove as
much dust as possible.
To remove the dust bag, follow the installation proce-
dures in reverse.
Installing paper dust bag (optional accessory)
Place the paper dust bag on the paper dust bag holder
with its front side upward. Insert the front fixing card-
board of the paper dust bag into the groove of the paper
dust bag holder. (Fig. 7)
Then press the upper part of the front fixing cardboard in
arrow direction to hook it onto the claws. (Fig. 8)
Insert the notch of the paper dust bag into the guide of
the paper dust bag holder. Then install the paper dust
bag holder set on the tool. (Fig. 9 & 10)
NOTE:
• If you connect a Makita dust collector to this tool, more
efficient and cleaner operations can be performed.
OPERATION
Sanding operation (Fig. 11)
CAUTION:
• Never run the tool without the abrasive paper. You may
seriously damage the pad.
• Do not block motor vent with your finger or hand.
• Never force the tool. Excessive pressure may decrease
the sanding efficiency, damage the abrasive paper or
shorten tool life.
Hold the tool firmly with one hand on the switch handle
and the other hand on the front grip when performing the
tool. Turn the tool on and wait until it attains full speed.
Then gently place the tool on the workpiece surface.
Keep the pad flush with the workpiece and apply slight
pressure on the tool.
MAINTENANCE
CAUTION:
• Always be sure that the tool is switched off and
• Never use gasoline, benzine, thinner, alcohol or the
To maintain product SAFETY and RELIABILITY, repairs,
carbon brush inspection and replacement, any other
maintenance or adjustment should be performed by
Makita Authorized Service Centers, always using Makita
replacement parts.

OPTIONAL ACCESSORIES

CAUTION:
• These accessories or attachments are recommended
mark on the bag's
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Abrasive paper (with pre-punched holes)
• Velcro type of abrasive paper (with pre-punched holes)
• Joint 25 (for connecting to vacuum cleaner)
• Paper dust bag
• Paper dust bag holder
NOTE:
• Some items in the list may be included in the tool pack-
Noise
The typical A-weighted noise level determined according
to EN62841:
Vibration
The vibration total value (tri-axial vector sum) determined
according to EN62841:
• The declared vibration emission value has been mea-
• The declared vibration emission value may also be
WARNING:
• The vibration emission during actual use of the power
• Be sure to identify safety measures to protect the oper-
unplugged before attempting to perform inspection or
maintenance.
like. Discoloration, deformation or cracks may result.
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
age as standard accessories. They may differ from
country to country.
Sound pressure level (L
Sound power level (L
Uncertainty (K): 3 dB (A)
Wear ear protection
Work mode: sanding metal plate
Vibration emission (a
Uncertainty (K): 1.5 m/s
sured in accordance with the standard test method and
may be used for comparing one tool with another.
used in a preliminary assessment of exposure.
tool can differ from the declared emission value
depending on the ways in which the tool is used.
ator that are based on an estimation of exposure in the
actual conditions of use (taking account of all parts of
the operating cycle such as the times when the tool is
switched off and when it is running idle in addition to
the trigger time).
ENG905-1
): 84 dB (A)
pA
): 95 dB (A)
WA
ENG900-1
2
): 3.5 m/s
h
2
ENG901-1
5