Residual Risks - Black & Decker BES610 Mode D'emploi

Power tools are dangerous in the hands of untrained
users.
e. Maintain power tools and accessories. Check for
misalignment or binding of moving parts, breakage of
parts and any other condition that may affect the
power tools operation. If damaged, have the power
tool repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
h. Keep handles and grasping surfaces dry, clean and
free from oil and grease. Slippery handles and grasping
surfaces do not allow for safe handling and control of the
tool in unexpected situations.
6. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
Additional power tool safety warnings
@
Warning! Additional safety warnings for jigsaws
and reciprocating saws
Hold power tool by insulated gripping surfaces, when
u
performing an operation where the cutting accessory
may contact hidden wiring.
Cutting accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and could give
the operator an electric shock.
Use clamps or another practical way to secure and
u
support the workpiece to a stable platform.
Holding the work by hand or against your body leaves it
unstable and may lead to loss of control.
Keep hands away from cutting area. Never reach
u
underneath the work piece any reason. Do not insert
fingers or thumb into the vicinity of the reciprocating blade
and blade clamp. Do not stabilize the saw by gripping the
shoe.
Keep blades sharp. Dull or damaged blades may cause
u
the saw to swerve or stall under pressure. Always use the
appropriate type of saw blade for the workpiece material
and type of cut.
When cutting pipe or conduit, make sure that they are
u
free from water, electrical wiring, etc.
(Original instructions)
Do not touch the workpiece or the blade immediately
u
after operating the tool. They can become very hot.
Be aware of hidden hazards, before cutting into walls,
u
floors or ceilings, check for the location of wiring and
pipes.
The blade will continue to move after releasing the
u
switch. Always switch the tool off and wait for the saw
blade to come to a complete standstill before putting the
tool down.
Warning! Contact with, or inhalation of dusts arising from
cutting applications may endanger the health of the operator
and
possible bystanders. Wear a dust mask specifically designed
for protection against dust and fumes and ensure that persons
within or entering the work area are also protected.
The intended use is described in this instruction manual.
u
The use of any accessory or attachment or performance
u
of any operation with this tool other than those
recommended in this instruction manual may present a
risk of
personal injury and/or damage to property.
Safety of others
This tool is not intended for use by persons (including
u
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they
have been given supervision or instruction concerning use
of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not
u
play with the appliance.

Residual risks

Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
Injuries caused by touching any rotating/moving parts.
u
Injuries caused when changing any parts, blades or
u
accessories.
Injuries caused by prolonged use of a tool. When using
u
any tool for prolonged periods ensure you take regular
breaks.
Impairment of hearing.
u
Health hazards caused by breathing dust developed when
u
using your tool (example:- working with wood, especially
oak, beech and MDF.)
Vibration
The declared vibration emission values stated in the technical
data and the declaration of conformity have been measured in
ENGLISH
5