Environmental Protection - PEUGEOT ENERGYDrill-16LA Manuel D'utilisation

Additional Safety Rules For
Drill Presses
WARNING! For your own safety, do not try
to use your drill press or plug it in until it is
completely assembled and installed according
to the instructions, and until you have read and
understood this instruction manual.
1. This drill press is intended for use in dry conditions,
and for indoor use only.
2. Do not drill pieces of material too small to be
securely held.
3. Keep hands out of the path of drill bits. Avoid
awkward hand positions where a sudden slip could
cause your hand to move into the drill bit.
4. Do not install or use any drill bit that exceeds 175
mm in length or extends 150 mm below the chuck
jaws. They can suddenly bend outward or break.
5. Choose the right drill bits for your workpiece
materials. Do not use wire wheels, router bits,
shaper cutters, circle (fly) cutters, or rotary planers
on this drill press.
6. When drilling a large piece of material make sure it
is fully supported at the table height.
7. Do not perform any operation freehand. Use jigs,
clamps, fixtures or different tools for unstable work
pieces.
8. Do not drill the material too fast to avoid overloading
of the drill.
9. Make sure there are no nails or foreign objects in
the part of the workpiece to be drilled.
10. If the workpiece overhangs the table and will fall
or tip if not held, clamp it to the table or provide
auxiliary support.
11. When using a drill press vice, always fasten it to the
table.
12. Make sure all clamps and locks are firmly tightened
before drilling.
13. Do not perform layout assembly or set up work on
the table while the drill press is in operation.
14. Wear suitable personal protective equipment when
necessary, this could include:
- hearing protection to reduce the risk of induced
hearing loss;
- eye protection;
- respiratory protection to reduce the risk of
inhalation of harmful dust;
- gloves for handling drill bits (drill bits shall
be carried in a holder wherever practicable) and
rough material.
WARNING !
• Ensure that the arm is securely fixed when bevelling.
• Keep the floor area around the machine level, well
maintained and free of loose materials e.g. chips and
cut-offs.
• Use correctly sharpened drill bits. Observe the
maximum speed marked on the drill bit.
• When fitted with laser, no exchange with different type
of laser is permitted. Repairs shall only be carried out
by the laser manufacturer or an authorised agent.
• Refrain from removing any cut-offs or other parts of
the workpiece from the cutting area whilst the machine
is running and the drill press head is not in the rest
position.
• Ensure that the machine is always fixed to a bench,
whenever possible.
15. Never use the drill press near flammable liquids,
vapors, or gases.
16. Remove all nails that may be in the workpiece to
prevent sparking that could cause a fire.
17. To avoid fire or toxic reaction, never use gasoline,
naphtha acetone, lacquer thinner or similar highly
volatile solvents to clean the drill press.
18. Keep the drill press with proper footing on the table
or the ground to decrease noise and vibration.
19. Always use the designated carrying handle for
transportation.
WARNING! Noise can be a health hazard. When the
noise level exceeds 80 dB(A), be sure to wear ear
protection.
SYMBOLS
V .............volts
Hz... ........hertz
min ...........minutes
h ...............hours
ON O ..............OFF
minute
Wear safety goggles
Wear ear protection
Wear a breathing mask
Read and understand instruction manual: To
reduce the risk of injury, user and all bystanders
must read and understand instruction manual
before using this product.
Keep hands away from blade: Failure to keep
your hands away from the blade will result in
serious personal injury.

ENVIRONMENTAL PROTECTION

Waste electrical products should not be
disposed of with household waste. Please
recycle where facilities exist. Do not dispose
of electrical appliances as unsorted municipal
waste, use separate collection facilities. Contact
your local government for information regarding the
collection systems available. If electrical appliances
are disposed of in landfills or dumps, hazardous
substances can leak into the groundwater and get into
the food chain, damaging your health and wellbeing.
When replacing old appliances with new once, the
retailer is legally obligated to take back your old
appliance for disposal at least for free of charge.
Disposal of discarded material shall be in accordance
with local environmental regulations.
2
A .................................amperes
W.........................................watts
~....................alternating current
I ...........................................
-1
min ........revolutions per