Optional Accessories; General Maintenance; Lubrication - PEUGEOT ENERGYDrill-16LA Manuel D'utilisation

Optional Accessories

Item Art. No
Chuck & Key 96430
96431
96432
96433
Keyless Chuck 96436
96435
Drilling jig 96265
Vice 96221
96222
Drum Sanders kit 96155
96156
96157
Maintenance
WARNING: For your own safety, turn the switch off
and remove the plug from the power source outlet
before maintaining or lubricating your drill press.

GENERAL MAINTENANCE

Frequent blow out using an air compressor or dust
vacuum, any dust that accumulates inside the motor.
A coat of automotive paste wax applied to the table and
column will help to keep the surface clean.
WARNING: To avoid shock or fire hazard, if the power
lead is worn or cut in any way, replace it immediately.

LUBRICATION

All the drilling machine ball bearings are packed with
grease at factory, they required no further lubrication.
Periodically lubricate the gear and rack, table elevation
mechanism of the spindle and the rack (teeth) of the
quill.
Accessories Model No.
13mm
16mm Others
13mm
16mm Others
13mm
16mm Others
General Type All
75 mm (3")
95 mm (4") EnergyDrill-16LA
EnergyDrill-20LA/FL
25 pcs Sanding All
Drum Kit: 5 pcs
drums,
10 pcs #80
Sanding Sleeves,
10 pcs #120
Sanding Sleeves
10 pcs #80
Sanding Sleeves
10 pcs #120
Sanding Sleeves
Trouble Shooting
PROBLEM PROBLEM CAUSE
Chuck will not Dirt, grease or oil on
stay attached the tapered inside
to spindle. surface of the chuck
or on the spindle's
tapered surface
Noisy 1.Incorrect belt
operation tension.
2.Dry spindle.
3.Loose spindle
pulley.
4.Loose motor pulley.
Drill bit burns 1.Incorrect speed.
2.Chips not coming
out of hole.
3.Dull drill bit.
4.Feeding too slowly.
5.Not lubricated.
Drill leads off, 1.Hard grain in wood
hole not round or lengths of cutting
lips and/ or angle
not equal.
2.Bent drill bit
3.Drilled hole too big
Drill bit binds 1.Workpiece pinching
in workpiece. drill bit, or excessive
feed presure.
2.Improper belt
tension.
Excessive drill 1.Bent drill bit.
bit runout or 2.Worn spindle
wobble. bearings.
3.Drill bit not properly
installed in chuck.
4.Chuck not properly
installed.
Quill returns 1.Coil spring has
too slow or improper tension.
too fast.
Chuck will not 1.Dirt, grease, or
stay attached oil on the tapered
to spindle. inside surface of
It falls off chuck or on the
when trying to tapered surface of
install. the spindle.
The LASER 1.The batteries are
GUIDE will dead.
not turn on. 2.The battery contacts
need adjustment.
9
REMEDY SUGGESTED
Using household detergent,
clean the tapered surfaces of
chuck and spindle.
1.Adjust tension. See section
"Changing Speeds".
2.Lubricate spindle. See
"General Maintenance".
3.Check tightenness of
retaining nut on pulley, and
tighten if necessary.
4.Tighten set screw in motor
pulley.
1.Change speed.
2.Retract drill frequently to
clear chips.
3.Resharpen drill bit.
4.Feed fast enough – allow
drill to cut.
5.Lubricate drill.
1.Resharpen drill bit correctly.
2.Replace drill bit.
3. Drill a pilot hole
1.Support workpiece or clamp
it properly.
2.Adjust tension. See Section
"Changing Speeds".
1.Use a straight drill bit.
2.Replace bearings.
3.Install drill properly. See
"Changing Drill Bit."
4.Install chuck properly. See
"Assembly".
1.Adjust spring tension. See
Section "ADJUSTMENTS" -
(Chuck).
1.Using a non-alcohol based
cleaner, clean the tapered
surface of the chuck and
spindle to remove all dirt,
grease and oil. See Section
"ADJUSTMENTS" -
(Chuck).
1.Replace with new AAA
batteries.
2.Tap outside the bottom and
side of the laser housing
very lightly with the butt end
of a screwdriver. To avoid
getting bent, do not tap the
laser housing heavily.