Troubleshooting - Whirlpool WEE750H0HZ Mode D'emploi

First try the solutions suggested here. If you need further assistance or more recommendations that may help you avoid
a service call, refer to the warranty page in this manual or visit producthelp.www.whirlpool.com. In Canada, visit www.whirlpool.ca.
Contact us by mail with any questions or concerns at the address below:
In the U.S.A.:
Whirlpool Brand Home Appliances
Customer eXperience Center
553 Benson Road
Benton Harbor, MI 49022-2692
Please include a daytime phone number in your correspondence.
Problem Possible Causes and/or Solutions
Nothing will operate Power supply cord is unplugged: Plug into a grounded outlet.
Household fuse is blown or a circuit breaker is tripped: Replace the fuse or reset the circuit breaker.
If the problem continues, call an electrician.
The control displays an F9 or F9 E0 error code: The electrical outlet in the home may be miswired.
Contact a qualified electrician to verify the electrical supply.
Cooktop will not The control knob is not set correctly: Push in knob before turning to a setting.
operate
On ceramic glass models, the oven control lockout is set: See "Control Lock" in the "Feature Guide"
section.
Excessive heat Cookware is not the proper size: Use cookware about the same size as the surface cooking area, element,
around cookware
or surface burner. Cookware should not extend more than 1/2" (13 mm) outside the cooking area.
on cooktop
Cooktop cooking
Control knob set to incorrect heat level: See the "Cooktop" section.
results not
Range is not level: Level the range. See the Installation Instructions.
what expected
Cooktop element Element cycling due to a temperature limiter: This is normal operation. The element may cycle on and off
cycles on and off to keep the cooktop from overheating.
on High setting
Oven will not operate Delay Start is set: See the "Cook Time" section.
Control is locked: See "Control Lock" in the "Tools" section.
The range is in Demo Mode: Demo Mode will deactivate all oven elements. See "Info" in the "Tools"
section.
Electronic oven control set incorrectly: See the "Tools" and "More Modes" sections.
Oven temperature Oven temperature needs adjustment: See "Temperature Calibration" in the "More Modes" section.
too high or too low
Oven indicator Power to range is turned on or restored: See the "Tools" and "More Modes" sections. If the indicator
lights flash lights keep flashing, call for service.
Display shows Power failure: On some models, reset the clock, if needed. See "Preferences" in the "Tools" section.
messages
Error code (Display shows letter followed by number.): Depending on your model, press the Cancel
keypad to clear the display. See the "Tools" and "More Modes" sections. If it reappears, call for service.
Range is in Sabbath mode (display shows "Sabbath Mode"): See the "Sabbath Mode" section to exit
Sabbath mode.
Demo Mode (product is in Demo Mode): See the "Tools" section to exit Demo Mode.
Clean cycle did not Several cooking cycles between Clean cycles or spills on oven walls and doors: Run additional
work on all spills Clean cycles. Use the AquaLift
information.
Mineral deposits Tap water was used in the Clean cycle: Use distilled or filtered water in the Clean cycle.
are left on the oven
To remove deposits, use a cloth soaked with vinegar. Then use a cloth dampened with water to thoroughly
bottom after the
remove any vinegar residue.
Clean cycle
Range is not level: Mineral deposits will collect on dry areas of the oven bottom during the Clean cycle.
Level the range. See the Installation Instructions.
To remove deposits, use a cloth soaked with vinegar. Then use a cloth dampened with water to thoroughly
remove any vinegar residue.
20

TROUBLESHOOTING

In Canada:
Technology Cleaning Kit. See the "Clean Cycle" section for more
®
Whirlpool Brand Home Appliances
Customer eXperience Centre
200 - 6750 Century Ave.
Mississauga, Ontario L5N 0B7