Additional Safety Rules; Functional Description - Makita 3709 Manuel D'instructions

ENGLISH
1 Base
2 Scale
3 Bit protrusion
4 Clamping nut
5 Adjusting screw
6 Switch lever
7 Loosen
8 Tighten
9 Hold
10 Workpiece
11 Feed direction
SPECIFICATIONS
Model
Collet chuck capacity....................................6 mm or 1/4"
-1
No load speed (min )............................................ 30,000
Overall length ...................................................... 199 mm
Net weight............................................................... 1.5 kg
Safety class .............................................................
• Due to the continuing program of research and devel-
opment, the specifications herein are subject to change
without prior notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for flush trimming and profiling of
wood, plastic and similar materials.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety hints
For your own safety, please refer to enclosed safety
instructions.

ADDITIONAL SAFETY RULES

1. Hold tool by insulated gripping surfaces when
performing an operation where the cutting tool
may contact hidden wiring or its own cord. Con-
tact with a "live" wire will make exposed metal
parts of the tool "live" and shock the operator.
2. Wear hearing protection during extended period
of operation.
3. Handle the bits very carefully.
4. Check the bit carefully for cracks or damage
before operation.
Replace cracked or damaged bit immediately.
5. Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
6. Hold the tool firmly.
7. Keep hands away from rotating parts.
8. Make sure the bit is not contacting the work-
piece before the switch is turned on.
Explanation of general view
12 Bit revolving direction
13 View from the top of the tool
14 Straight guide
15 Base protector
16 Screws
17 Screwdriver
18 Bit
19 Templet
20 Templet guide
21 Bolt
22 Guide plate
9.
3709
10. Be careful of the bit rotating direction and the
11. Do not leave the tool running. Operate the tool
/II
12. Always switch off and wait for the bit to come to
13. Do not touch the bit immediately after operation;
14. Always lead the power supply cord away from
15. Do not smear the tool base carelessly with thin-
16. Draw attention to the need to use cutters of the
SAVE THESE INSTRUCTIONS.

FUNCTIONAL DESCRIPTION

CAUTION:
• Always be sure that the tool is switched off and
unplugged before adjusting or checking function on the
ENB054-1
tool.
Adjusting bit protrusion (Fig. 1)
To adjust the bit protrusion, loosen the clamping nut and
move the tool base up or down as desired by turning the
adjusting screw. After adjusting, tighten the clamping nut
firmly to secure the tool base.
Switch action (Fig. 2)
To start the tool, move the switch lever to the I (ON) posi-
tion. To stop the tool, move the switch lever to the O
(OFF) position.
23 Wing nut
24 Clamp screw (A)
25 Centre hole
26 Nail
27 Clamp screw (B)
28 Trimmer guide
29 Guide roller
30 Limit mark
31 Brush holder cap
Before using the tool on an actual workpiece, let
it run for a while.
Watch for vibration or wobbling that could indi-
cate improperly installed bit.
feed direction.
only when hand-held.
a complete stop before removing the tool from
workpiece.
it may be extremely hot and could burn your
skin.
the tool towards the rear.
ner, gasoline, oil or the like.
They may cause cracks in the tool base.
correct shank diameter and which are suitable
for the speed of the tool.
5