KIKKA BOO TWISTER Mode D'emploi page 6

3.1. Check the seat is ready to be installed rearward facing (Group 0+) as shown in g. 3.3. Recline the seat fully. Pull the lever (G) forward
and adjust the angle of recline to position 4 without releasing the lever. If it is necessary swivel the seat 180º to place the seat in the opposite
direction of travel ( g. 3.2). Release the lever when the seat is in the desired position.
3.2. By turning the Isoclick Fix arms, extract both arms (N) located in the base of the seat ( g. 3.3).
3.3. Place the seat in the back seat of the vehicle in the opposite direction of travel.
3.4. Hold the safety seat with both hands and insert the two Isoclick Fix arms (N) rmly into the vehicle´s iso x anchoring points until they
fasten with a click on both sides. The red button will change to green on both sides ( g. 3.4).
3.5. Shake the seat to check that it is correctly anchored to the vehicle's ISOFIX points.
3.6. Pass the abdominal strap of the seat belt through the back support slots (K) as g.3.5 shows. Buckle the vehicle seat belt until you hear
a click.
3.7. Take up the remaining slack of the diagonal section of the 3-point seat belt ( g. 3.6). and make sure it is as tight tting as possible.
Ensure the straps are not twisted or knotted at any point.
Uninstalling the Isoclick Fix system
3.8.To free the Isoclick Fix anchoring, press the Isoclick Fix system unlock buttons, in order to free the seat from the vehicle ISOFIX anchoring
system ( g. 6.7 and 6.8).
4. PLACING THE CHILD IN THE SEAT GROUP 0+
Proper adjustment of the height of the harness ensures the child will be seated correctly. The harness should be adjusted to the height of the
child's shoulder or slightly above; never behind the child's back or level with the ears ( g. 4.1).
4.1. L oosen the harness straps by pulling them gently while pressing the harness adjustment button (E) ( g. 4.2). Tip: Only pull on the
harness straps. Not the shoulder pads.
4.2. R elease the buckle (D) to make it easier to seat the child ( g.4.3).
4.3. Place the child in the seat.
4.4. Secure the child in the harness by joining the two parts of the clasp and fastening the buckle (D) until you hear a click ( g. 4.4).
4.5. Gently pull the harness adjustment strap to achieve the correct tension (F) ( g. 4.5). Remember that in order to ensure the child's safety
the harnesses should t tightly.
5. ADJUSTING THE headrest HEIGHT
Proper adjustment of the height of the headrest ensures the child will be seated correctly. The headrest should be adjusted to ensure that
the harness straps (B) should be adjusted to the height of the child's shoulder or slightly above; never behind the child's back or level with
the ears ( g. 4.1).
5.1. L oosen the harness straps (B) by pulling them gently while pressing the harness adjustment button (E) ( g. 5.1). Tip: Only pull on the
harness straps. Not the shoulder pads.
5.2. Adjust the headrest according to the child´s height by pulling the headrest height regulator (A) adjusting the harness to the height of
the child´s shoulder or slightly above ( g. 5.2).
6. INSTALLING THE CAR SEAT. GROUP 1
NOTICE: GROUP 1 only from 9 months to 4 years approx. (9-18 kg)
6.1. Ensure the seat is not in a reclined position (the indicator should be in position 1) and is ready to install in forward position (Group 1) as
shown in g. 6.1. Pull the lever (G) forward and adjust the angle of recline to position 1 without releasing the lever. If it is necessary swivel
the seat 180º to place the seat in the direction of travel ( g. 6.1.A). Release the lever when the seat is in the desired position.
6.2. By turning the Isoclick Fix arms, extract both arms (N) located in the base of the seat ( g. 6.2).
6.3. Place the child safety seat in the back seat of the vehicle facing in the direction of travel ( g. 6.3).
6.4. Hold the safety seat with both hands and insert the two Isoclick Fix arms (N) rmly into the vehicle´s iso x anchoring points until they
fasten with a click on both sides. The red button will change to green on both sides ( g.6.3).
6.5. Pass the vehicle seat belt through the slot on the back of the safety seat (M) until it appears at the exit ( g. 6.4). Buckle the vehicle seat
belt until you hear a click ( g. 6.5).
6.6. Take up the slack by pulling the abdominal section of the belt until it is as tight- tting as possible ( g 6.6).
6.7. Ensure the straps are not twisted at any point.
ENGLISH