Pedestal Assembly - Honeywell EFY-041 Serie Guide D'utilisation

16. A loose fit between the AC outlet
(receptacle) and plug may cause
overheating and a distortion of the
plug. Contact a qualified electrician
wto replace loose or worn outlet.
17. Do not operate any fan with a damaged
cord or plug. Discard any damaged fan,
return the fan to the retailer where the
fan was purchased, or request a return
authorization to return to Kaz, Inc. for
examination and/or repair.
FUSED SAFETY PLUG - FOR US ONLY
This fan features a patented fused safety plug which is designed to cut off electric current to the
fan if an electrical fault occurs. Please see below for more information on how to properly use
your fan and replace the safety plug fuse, if needed.
USER SERVICING INSTRUCTIONS
• Grasp plug and remove from the receptacle or other outlet device.
Do not unplug by pulling on cord.
• If your fan loses power and you suspect that the fuse on your fan
has blown, you should first remove the spare fuse holder attached
to the cord plug (Fig. 1). Remove the spare fuse from the plastic
spare fuse holder, and set the spare fuse aside (Fig. 2).
• You can gain access to the blown fuse by sliding open the door
found on the side of the plug. Slide the door outward until the
blown fuse is fully visible (Fig. 3).
• Carefully remove the blown fuse and snap the replacement fuse
into place. Risk of fire. Replace fuse only with 2.5 Amp, 125 volt
fuse (provided with product). Fully close the fuse door by sliding
back into place. Discard the blown fuse. The plug should now be
ready for normal use.
• Risk of fire. Do not replace attachment plug. Contains a safety
device (fuse) that should not be removed. Discard product if the
attachment plug is damaged.
• If you need further information on how or when to replace the
fuse in the safety plug, please contact Kaz Consumer Relations
Department by visiting our website at www.kaz.com or calling
1-800-477-0457.
2
18. Do not run fan cord under carpeting. Do
not cover cord with throw rugs, runners,
or similar coverings. Do not route cord
under furniture or appliances. Arrange
cord away from traffic areas and where it
will not be tripped over.
WARNING: To Reduce The Risk of Fire or
Electric Shock, Do Not Use This Fan With
Any Solid-State Speed Control Device,
other than the one supplied.
Fig. 1
Fig. 2
Fig. 3
ASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS FOR LOW FAN HEIGHT OPTION
A. Base Assembly
• Align the two portions of the circular base and snap together by
gently pushing the 4 round extrusions (Fig. 1, Item A) into the
adjacent circles of the connecting piece. (Fig. 1, Item B).
• Place the power cord through the center of the 2 halves of the
base assembly.
B. Securing the Tower Fan to the Base
• Carefully turn the fan on its side.
• Pull any slack out of the power cord. Align the base arrow
marked as with the tower fan arrow marked as
base clockwise to lock the tower fan in place (Fig. 2) .
• Secure the base assembly to the tower fan by inserting and
tightening the thumb screw to the bottom of the base (Fig. 3).
C. Securing the Cord to the Base
• With the fan on its side, locate the cord holding bracket on the
bottom of the base.
• Gently pull any slack out of the power cord, place the power
cord securely in the power cord holding bracket and secure the
power cord bracket over the power cord (Fig. 4).
• Return the tower fan to its upright position.
Note: Do not operate the tower fan unless it is in its proper,
upright position.
Note: Only one thumb screw is needed for the low height option.
Do not discard the additional screws as they will be needed for
Tall Height Option.
D. Placing the Remote Control in the Storage Area
• Locate the remote control that has been provided with the tower
fan. Make sure that the remote control is not thrown out with
the packing materials.
• Install batteries into the remote control battery compartment
(see Battery Installation/Replacement Instructions).
• Place the remote control in the recessed remote holder located
on the top of the fan (Fig. 5).
ASSEMBLY INSTRUCTIONS FOR TALL FAN HEIGHT OPTION
(USING PEDESTAL HEIGHT EXTENDER)
NOTE: Product is most stable when pedestal extender is not used.
A. Pedestal Assembly
• Line up the left and right pedestal assembly and firmly snap
together (Fig. 6).
Fig. 1
A
B
Base Assembly
Fig. 2
. Rotate the
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Pedestal Assembly
3