Bosch PROFESSIONAL GSR 12 VE-2 Instructions D'emploi page 18

OBJ_DOKU-3295-002.fm Page 18 Wednesday, November 22, 2006 12:44 PM
Declaration of Conformity
We declare under our sole responsibility that this prod-
uct is in conformity with the following standards or
standardization documents: EN 60745 according to
the provisions of the
98/37/EC.
Dr. Egbert Schneider Dr. Eckerhard Strötgen
Senior Vice President Head of Product
Engineering Certification
10.05.2006, Robert Bosch GmbH, Power Tools Division
D-70145 Leinfelden-Echterdingen
Noise/Vibration Information
Measured values determined according to EN 60745.
GSR 12 VE-2 / GSR 14,4 VE-2 / GSR 18 VE-2:
Typically the A-weighted sound pressure level of the
machine is 72 dB(A). Uncertainty K=3 dB.
The noise level when working can exceed 85 dB(A).
Wear hearing protection!
Overall vibrational value (vector sum of three direc-
tions) determined according to EN 60745:
Drilling in metal: Vibrational emission value
2
a =2.5 m/s , uncertainty K=1.5 m/s
h
Screwdriving: Vibrational emission value a
2
uncertainty K=1.5 m/s .
GSB 12 VE-2 / GSB 14,4 VE-2 / GSB 18 VE-2:
Typically the A-weighted noise level of the machine is:
sound pressure level 90 dB(A); sound power level
101 dB(A). Uncertainty K=3 dB.
Wear hearing protection!
Overall vibrational value (vector sum of three direc-
tions) determined according to EN 60745:
Drilling in metal: Vibrational emission value
2
a =3.5 m/s , uncertainty K=1.5 m/s
h
Impact drilling in concrete: Vibrational emission value
2
a =13 m/s , uncertainty K=1.5 m/s
h
Screwdriving: Vibrational emission value a
2
uncertainty K=1.5 m/s .
GSR 12 VE-2 / GSR 14,4 VE-2 / GSR 18 VE-2 /
GSB 12 VE-2 / GSB 14,4 VE-2 / GSB 18 VE-2:
The vibration emission level given in
WARNING
this information sheet has been meas-
ured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with
another.
The vibration emission level will vary because of the
ways in which a power tool can be used and may
increase above the level given in this information sheet.
This could lead to a significant underestimate of expo-
sure when the tool is used regularly in such a way.
18 | English
directives 89/336/EEC,
2
,
2
=2.5 m/s ,
h
2
,
2
,
2
=2.5 m/s ,
h
Note: To be accurate, an estimation of the level of
exposure to vibration experienced during a given period
of work should also take into account the times when
the tool is switched off and when it is running but not
actually doing the job. This may significantly reduce the
exposure level over the total working period.
Assembly
Battery Charging
A battery that is new or has not been used for a longer
period does not develop its full capacity until after
approx. 5 charging/discharging cycles.
To remove the battery 8 press the unlocking buttons 7
and pull out the battery downwards. Do not exert any
force.
The battery is equipped with a NTC temperature con-
trol which allows charging only within a temperature
range of between 0 °C and 45 °C. A long battery serv-
ice life is achieved in this manner.
A significantly reduced working period after charging
indicates that the battery is used and must be replaced.
Observe the notes for disposal.
Auxiliary Handle (GSR 18 VE-2 /
GSB 18 VE-2) (see figure A)
Operate your machine only with the auxiliary
handle 6.
The auxiliary handle 6 can be set to any position for a
secure and low-fatigue working posture.
Turn the bottom part of the auxiliary handle 6 in coun-
terclockwise direction and swivel the auxiliary handle 6
to the desired position. Then retighten the bottom part
of the auxiliary handle 6 by turning in clockwise direc-
tion.
The clamping band 12 of the auxiliary handle must be
seated in the corresponding groove.
2 609 932 515 • 22.11.06